전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

LM2633 데이터시트(PDF) 34 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
부품명 LM2633
상세설명  Advanced Two-Phase Synchronous Triple Regulator Controller for Notebook CPUs
PDF  40 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  NSC [National Semiconductor (TI)]
홈페이지  http://www.national.com
Logo NSC - National Semiconductor (TI)

LM2633 데이터시트(HTML) 34 Page - National Semiconductor (TI)

Back Button LM2633 Datasheet HTML 30Page - National Semiconductor (TI) LM2633 Datasheet HTML 31Page - National Semiconductor (TI) LM2633 Datasheet HTML 32Page - National Semiconductor (TI) LM2633 Datasheet HTML 33Page - National Semiconductor (TI) LM2633 Datasheet HTML 34Page - National Semiconductor (TI) LM2633 Datasheet HTML 35Page - National Semiconductor (TI) LM2633 Datasheet HTML 36Page - National Semiconductor (TI) LM2633 Datasheet HTML 37Page - National Semiconductor (TI) LM2633 Datasheet HTML 38Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 34 / 40 page
background image
Control Loop Design (Continued)
(45)
(46)
Back to the previous example. Let B = K, f
z1 =fp,fp2 =fz,fz2
=f
n, then:
f
c_o = 5.1 x 310Hz = 1581Hz
The corresponding Bode plots of the compensation network
and the loop transfer function are shown in
Figure 12 and
Figure 13 respectively.
It can be seen from
Figure 13 that the crossover frequency is
20kHz, and the phase margin is about 84 degrees.
One thing that should be pointed out is this Bode plot is only
for the 0.4
Ω load. That is, when load current is 4A. If load
current is lower than 4A, the portion of the gain plot from the
corresponding f
p to 310Hz will be −40dB/dec. If load current
is higher than 4A, then the portion of the gain plot from
310Hz to fp will be flat. However, this usually does not have
much effect on the cross-over frequency and phase margin
because it happens at low frequencies.
If a shorter recovery time is desired during a load transient,
f
z1 can be increased so that the gain of the loop transfer
function becomes higher. However, try not to let f
z1 be higher
than the desired cross-over frequency, otherwise phase mar-
gin can be too low.
Figure 14 shows a situation where f
z1 is
placed at a higher frequency than the f
p, which results in a
−40 dB/dec section before the cross-over frequency. Notice
the phase margin is lower.
Sometimes the slow transient response is caused by the
current source and sink capability of the error amplifier.
Reducing the value of the compensation capacitor helps, but
make sure the small-signal loop is stable.
The power stage component selection can be significantly
different from the example values.
Figure 15 shows how the
two high frequency poles of a current-mode-control buck
regulator change with the Q value.
20000876
FIGURE 12. Example Compensation Transfer Function
20000877
FIGURE 13. Example Loop Transfer Function
200008D6
FIGURE 14. Higher Low Frequency Gain
www.national.com
34



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com