WM8281ECSSLASHR datasheet(288/392 Pages) CIRRUS

288 / 392 page

WM8281

288

Rev 4.0

FLL INTERRUPTS AND GPIO OUTPUT

For each FLL, the WM8281 supports

an ‘FLL Clock OK’ signal which, when asserted, indicates that

the FLL has started up and is providing an output clock

. Each FLL also supports an ‘FLL Lock’ signal

which indicates whether FLL Lock has been achieved (ie. the FLL is locked to the input reference

signal).

The FLL Clock OK status and FLL Lock status are inputs to the Interrupt control circuit and can be

used to trigger an Interrupt event -

see “Interrupts”. Note that these Interrupt signals are de-bounced,

and require clocking to be present in order to assert the respective Interrupt; either the 32kHz clock,

or the SYSCLK signal, must be enabled to trigger an Interrupt from the FLL signals.

The FLL Clock OK and FLL Lock signals can be output directly on a GPIO pin as an external

indication of the

FLL status. See “General Purpose Input / Output” to configure a GPIO pin for these

functions. (These GPIO outputs are not de-bounced, and do not require clocking to be present.)

Clock output signals derived from the FLL can be output on a GPIO pin.

See “General Purpose Input /

Output

” to configure a GPIO pin for this function.

The FLL clocking configuration is illustrated in Figure 71.

EXAMPLE FLL CALCULATION

The following example illustrates how to derive the FLL1 registers to generate 147.456 MHz output

(FOUT) from a 12.000 MHz reference clock (FREF):



Set FLL1_REFCLK_DIV in order to generate FREF <=13.5MHz:

FLL1_REFCLK_DIV = 00 (divide by 1)



Set FLL1_OUTDIV for the required output frequency as shown in Table 102:-

FOUT = 147.456 MHz, therefore FLL1_OUTDIV = 2h (divide by 2)



Set FLL1_FRATIO for the given reference frequency as shown in Table 103:

FREF = 12MHz, therefore FLL1_FRATIO = 0h (divide by 1)



Calculate FVCO as given by FVCO = FOUT x FLL1_OUTDIV:-

FVCO = 147.456 x 2 = 294.912 MHz



Calculate N.K as given by N.K = FVCO / (FLL1_FRATIO x 3 x FREF):

N.K = 294.912 / (1 x 3 x 12) = 8.192



Confirm that a non-integer value has been calculated for N.K.



Confirm that the input frequency, FREF, is less than the applicable limit shown in Table 104.



Determine FLL1_N from the integer portion of N.K:-

FLL1_N = 8 (008h)



Determine GCD(FLL), as given by GCD(FLL) = GCD(FLL1_FRATIO x FREF, FVCO / 3):

GCD(FLL) = GCD(1 x 12000000, 294912000 / 3) = 96000



Determine FLL1_THETA, as given by

FLL1_THETA = ((FVCO / 3) - (FLL1_N x FLL1_FRATIO x FREF)) / GCD(FLL):

FLL1_THETA = ((294912000 / 3) - (8 x 1 x 12000000)) / 96000

FLL1_THETA = 24 (0018h)



Determine FLL_LAMBDA, as given by

FLL1_LAMBDA = (FLL1_FRATIO x FREF) / GCD(FLL):

FLL1_LAMBDA = (1 x 12000000) / 96000

FLL1_LAMBDA = 125 (007Dh)

WM8281ECS/R 데이터시트(PDF) 288 Page - Cirrus Logic

WM8281ECS/R 데이터시트(HTML) 288 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL