SPECIFICATION

MODEL

PLM-12

-700

RATED CURRENT

RATED POWER

OUTPUT

SETUP TIME

FREQUENCY RANGE

POWER FACTOR

EFFICIENCY

(Typ.)

AC CURRENT

INPUT

INRUSH CURRENT(Typ.)

LEAKAGE CURRENT

SAFETY STANDARDS

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSION

OTHERS

NOTE

PACKING

SHORT CIRCUIT

11 ~ 18V

0.7A

12.6W

2.4Vp-p

±5.0%

Blank type: 500ms / 115VAC, 230VAC at full load;

E type: 500ms / 230VAC at full load

Blank type: 110 ~ 295VAC

156 ~ 417VDC; E type: 180 ~ 295VAC

254~ 417VDC

47 ~ 63Hz

Blank type: 0.15A/115VAC

0.08A/230VAC

0.07A/277VAC; E type: 0.08A/230VAC 0.07A/277VAC

COLD START 15A(twidth=50 s measured at 50% Ipeak) at 230VAC

μ

0.25mA / 240VAC

Hiccup mode, recovers automatically after fault condition is removed.

Compliance to EN61000-4-2,3,4,5,6,8,11;EN61547, light industry level, criteria B(surge 2KV)

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms/500VDC / 25

/ 70%RH

℃

-30 ~ +50

℃

20 ~ 90% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

℃

±℃

℃

0.06%/

(0 ~ 50

)

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

RIPPLE & NOISE

ENVIRONMENT

SAFETY &

EMC

PROTECTION

PLM-12

-350

0.35A

12.6W

3.6Vp-p

22 ~ 36V

File Name:PLM-12-SPEC 2015-11-02

145*38*22mm (L*W*H)

808.162Khrs min.

MIL-HDBK-217F (25

)

℃

0.126Kg;60pcs/8.6 Kg/0.48CUFT

PLM-12

-1050

7 ~ 12V

1.05A

12.6W

1.8Vp-p

83%

81%

85%

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Please see AC input voltage drop vs. output current characteristics table.

""

4. Derating may be needed under low input voltage, please check the static characteristic for more details.

5. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

PF

0.97/115VAC,PF

0.95/230VAC,PF>0.9/277VAC(at full load)(Please refer to "Power Factor Characteristic" curve)

≥≥

Compliance to EN55015, GB17743, GB17625.1

EN61000-3-2 Class C(

60% load);EN61000-3-3

(for E type only),

≥

EMC IMMUNITY

EMC EMISSION

22V

42V

16V

12W Single Output LED Power Supply

PLM-12

-500

15 ~ 24V

0.5A

12W

2.4Vp-p

84%

30V

Blank type

E type

Blank type

E type

PF

0.95/230VAC,PF

0.9/277VAC (at full load)(Please refer to "Power Factor Characteristic" curve)

≥≥

3.6Vp-p

5.5Vp-p

2.7Vp-p

3.6Vp-p

Blank type

E type

THD< 20% when output loading 60% at 115VAC/230VAC input and output loading 75% at 277VAC input

≧≧

TOTAL HARMONIC

DISTORTION

MAX. No. of PSUs on 16A

CIRCUIT BREAKER

160 units (circuit breaker of type B) / 160 units (circuit breaker of type C) at 230VAC

82%

78%

84%

83%

Blank type

E type

THD< 20% when output loading 60% at 230VAC input and output loading 75% at 277VAC input

≧≧

GB19510.14,GB19510.1

,

(for E type only) IP30 approved

UL8750, CSA C22.2 No. 250.13-12(for Blank type only); ENEC EN61347-1, EN61347-2-13, EN62384,