| 전자부품 데이터시트 검색엔진 |
|
W39V040FAQ 데이터시트(PDF) 5 Page - Winbond |
|
|
|||||||||||||||||||||||||||||
W39V040FAQ 데이터시트(HTML) 5 Page - Winbond |
|
5 / 36 page ![]() W39V040FA Publication Release Date: December 19, 2002 - 5 - Revision A2 Hardware Data Protection The integrity of the data stored in the W39V040FA is also hardware protected in the following ways: (1) Noise/Glitch Protection: A #WE pulse of less than 15 nS in duration will not initiate a write cycle. (2) VDD Power Up/Down Detection: The programming and read operation are inhibited when VDD is less than 1.5V typical. (3) Write Inhibit Mode: Forcing #OE low or #WE high will inhibit the write operation. This prevents inadvertent writes during power-up or power-down periods. (4) VDD power-on delay: When VDD has reached its sense level, the device will automatically time-out 5 mS before any write (erase/program) operation. Data Polling (DQ7)- Write Status Detection The W39V040FA includes a data polling feature to indicate the end of a program or erase cycle. When the W39V040FA is in the internal program or erase cycle, any attempts to read DQ7 of the last byte loaded will receive the complement of the true data. Once the program or erase cycle is completed, DQ7 will show the true data. Note that DQ7 will show logical "0" during the erase cycle, and when erase cycle has been completed it becomes logical "1" or true data. Toggle Bit (DQ6)- Write Status Detection In addition to data polling, the W39V040FA provides another method for determining the end of a program cycle. During the internal program or erase cycle, any consecutive attempts to read DQ6 will produce alternating 0's and 1's. When the program or erase cycle is completed, this toggling between 0's and 1's will stop. The device is then ready for the next operation. Register There are three kinds of registers on this device, the General Purpose Input Registers, the Block Lock Control Registers and Product Identification Registers. Users can access these registers through respective address in the 4Gbytes memory map. There are detail descriptions in the sections below. General Purpose Inputs Register This register reads the FGPI[4:0] pins on the W39V040FA.This is a pass-through register which can read via memory address FFBC0100(hex). Since it is pass-through register, there is no default value. GPI Register Table BIT FUNCTION 7 − 5 Reserved 4 Read FGPI4 pin status 3 Read FGPI3 pin status 2 Read FGPI2 pin status 1 Read FGPI1 pin status 0 Read FGPI0 pin status |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |