| 전자부품 데이터시트 검색엔진 |
|
HT56RB688 데이터시트(PDF) 42 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT56RB688 데이터시트(HTML) 42 Page - Holtek Semiconductor Inc |
|
42 / 164 page ![]() Clock Source The LCD clock source is the internal clock signal fSUB divided by 8 using an internal divider circuit. The fSUB internal clock is supplied by either the internal 32kHz RC oscillator (LIRC) or the external 32.768kHz oscillator (LXT), the choice of which is determined by a configuration option. For proper LCD operation, this arrangement is provided to generate an ideal LCD clock source frequency of 4kHz. f SUB Clock Source LCD Clock Frequency Internal 32kHz oscillator (LIRC) 4kHz External 32.768kHz oscillator (LXT) 4kHz LCD Clock Source LCD Driver Output When the LCDEN bit in the LCDCTRL register is set to 1, the COM and SEG lines will be setup as LCD driver pins to drive the LCD display. The number of COM and SEG outputs supplied by the LCD driver and its biasing and duty selections are dependent upon how the LCD control bits are programmed. The Bias Type is R type and the bias resistor can be selected using the RSEL1 and RSEL0 bits in the LCDCTRL register. The nature of Liquid Crystal Displays require that only AC voltages can be applied to their pixels as the application of DC voltages to LCD pixels may cause permanent damage. For this reason the relative contrast of an LCD display is controlled by the actual RMS voltage applied to each pixel, which is equal to the RMS value of the voltage on the COM pin minus the voltage applied to the SEG pin. This differential RMS voltage must be greater than the LCD saturation voltage for the pixel to be on and less than the threshold voltage for the pixel to be off. The requirement to limit the DC voltage to zero and to control as many pixels as possible with a minimum number of connections requires that both a time and amplitude signal is generated and applied to the application LCD. These time and amplitude varying signals are automatically generated by the LCD driver circuits in the microcontroller. What is known as the duty determines the number of common lines used, which are also known as backplanes or COMs. The duty which is chosen by a control bit to have a value of 1/8 and 1/16 and which equates to a COM number of 8 and 16 therefore defines the number of time divisions within each LCD signal frame. Two types of signal generation are also provided, known as Type A and Type B, the required type is selected via the TYPE bit in the LCDCTRL register. Type B offers lower frequency signals, however lower frequencies may introduce flickering and influence display clarity. LCD Control Register - LCDCTRL Bit 76543210 Name TYPE ¾ DTYC BIAS1 BIAS0 RSEL1 RSEL0 LCDEN R/W R/W ¾ R/W R/W R/W R/W R/W R/W POR 0 ¾ 000000 Bit 7 TYPE: LCD Type selection bit 0: Type A 1: Type B Bit 6 Unimplemented, read as ²0² Bit 5 DTYC: LCD Duty selection bit 0: 1/8 duty 1: 1/16 duty Bit 4~3 BIAS1~BIAS0: LCD Bias selection bits 00: 1/3 bias 01: 1/4 bias 10: 1/5 bias 11: Reserved Rev. 1.10 42 April 15, 2013 HT56RB688 TinyPowerTM A/D type Smart Card OTP MCU with LCD, DAC, ISO 7816 and USB Interfaces |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |