전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

SM5950AM 데이터시트(PDF) 11 Page - Nippon Precision Circuits Inc

부품명 SM5950AM
상세설명  Asynchronous Sample Rate Converter
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  NPC [Nippon Precision Circuits Inc]
홈페이지  http://www.npc.co.jp/en
Logo NPC - Nippon Precision Circuits Inc

SM5950AM 데이터시트(HTML) 11 Page - Nippon Precision Circuits Inc

Back Button SM5950AM Datasheet HTML 7Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 8Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 9Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 10Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 11Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 12Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 13Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 14Page - Nippon Precision Circuits Inc SM5950AM Datasheet HTML 15Page - Nippon Precision Circuits Inc Next Button
Zoom Inzoom in Zoom Outzoom out
 11 / 20 page
background image
SM5950AM
NIPPON PRECISION CIRCUITS INC.—11
System Reset (RSTN)
The SM5950AM must be reset if any of the following conditions occur during normal operation. A reset pulse
is a LOW-level pulse applied to RSTN, although the reset operation actually occurs on the rising edge of the
LOW-level pulse.
I
When the power supply is applied
A reset (RSTN = LOW to HIGH) is required when the power supply voltage is applied and after the LRCI,
BCKI, SCKO (and LRCO, BCKO if in slave mode) clocks have stabilized.
I
When the LRCI and BCKI clocks are interrupted
This occurs when the sampling frequency is switched, when clocks stop due to a condition in a previous stage,
when the LRCI, BCKI clocks are dynamically switched, or when otherwise the clocks are not continuous.
A reset (RSTN = LOW to HIGH) is required after the LRCI, BCKI clocks have stabilized.
I
When the SCKO (and LRCO, BCKO if in slave mode) clocks are interrupted
This occurs when the sampling frequency is switched, when clocks stop due to a condition in a previous stage,
when the SCKO, LRCO, BCKO clocks are dynamically switched, or when otherwise the clocks are not contin-
uous.
A reset (RSTN = LOW to HIGH) is required after the SCKO, LRCO, BCKO clocks have stabilized.
A reset pulse is required under these conditions because the conversion ratio calculated based on such non-con-
tinuous clocks will result in an incorrect conversion ratio, and hence the output data will have incorrect values.
Output state during reset interval
DOUT is tied LOW during the reset interval (refer to section "Direct Mute" for operation after the reset is
released). In master mode, the LRCO and BCKO clocks are also tied LOW.
Direct Mute (DMUTE)
Direct mute ON/OFF
Other mute operations
Direct mute also occurs at system reset.
DMUTE
Function
L
Audio data output starts from the next output word.
H
0 data is output from the next output word.
RSTN
Function
L
0 data is output from the next output word.
H
Computed data output starts after 8 output word cycles.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com