ADE9000 datasheet(58/73 Pages) AD

58 / 73 page

Data Sheet

ADE9000

Rev. A | Page 57 of 72

Addr. Name

Bits

Bit Name

Settings Description

Reset

Access

REVPSUM3

This bit indicates the sign of the last CF3 pulse. A

zero indicates that the pulse was from negative

energy and a one indicates that the energy was

positive. This bit is updated when a CF3 pulse is

output, when the CF3 pin goes from high to low.

0x0

REVPSUM2

This bit indicates the sign of the last CF2 pulse. A

zero indicates that the pulse was from negative

energy and a one indicates that the energy was

positive. This bit is updated when a CF2 pulse is

output, when the CF2 pin goes from high to low.

0x0

REVPSUM1

This bit indicates the sign of the last CF1 pulse. A

zero indicates that the pulse was from negative

energy and a one indicates that the energy was

positive. This bit is updated when a CF1 pulse is

output, when the CF1 pin goes from high to low.

0x0

SWELLC

This bit is equal to one when the Phase C

voltage is in the swell condition and is zero

when it is not in a swell condition.

0x0

SWELLB

This bit is equal to one when the Phase B voltage

is in the swell condition and is zero when it is not

in a swell condition.

0x0

SWELLA

This bit is equal to one when the Phase A

voltage is in the swell condition and is zero

when it is not in a swell condition.

0x0

DIPC

This bit is equal to one when the Phase C

voltage is in the dip condition and is zero when

it is not in a dip condition.

0x0

DIPB

This bit is equal to one when the Phase B voltage

is in the dip condition and is zero when it is not

in a dip condition

0x0

DIPA

This bit is equal to one when the Phase A

voltage is in the dip condition and is zero when

it is not in a dip condition.

0x0

0x405 MASK0

[31:26] RESERVED

Reserved.

0x0

TEMP_RDY_MASK

Set this bit to enable an interrupt when a new

temperature measurement is available.

0x0

R/W

MISMTCH

Set this bit to enable an interrupt when there is a

change in the relationship between ISUMRMS

and ISUMLVL.

0x0

R/W

COH_WFB_FULL

Set this bit to enable an interrupt when the

waveform buffer is full with resampled data,

which is selected when WF_CAP_SEL = 0 in the

WFB_CFG register.

0x0

R/W

WFB_TRIG

Set this bit to enable an interrupt when one of

the events configured in WFB_TRIG_CFG occurs.

0x0

R/W

THD_PF_RDY

Set this bit to enable an interrupt when the THD

and power factor measurements are updated,

every 1.024 sec.

0x0

R/W

RMS1012RDY

Set this bit to enable an interrupt when the

10 cycle rms/12 cycle rms values are updated.

0x0

R/W

RMSONERDY

Set this bit to enable an interrupt when the fast

rms½ values are updated.

0x0

R/W

PWRRDY

Set this bit to enable an interrupt when the

power values in the xWATT_ACC, xVA_ACC,

xVAR_ACC, xFWATT_ACC, xFVA_ACC, and

xFVAR_ACC registers update, after PWR_TIME

8 kSPS samples.

0x0

R/W

ADE9000 데이터시트(PDF) 58 Page - Analog Devices

ADE9000 데이터시트(HTML) 58 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

데이터시트 다운로드

링크 URL