FMS6404CSX datasheet(8/11 Pages) ONSEMI

8 / 11 page

www.fairchildsemi.com

FMS6404 • Rev. 1.0.0

Applications Information

Layout Considerations

General layout and supply bypassing play a major role

high-frequency

performance

and

thermal

characteristics. Fairchild offers a four-layer board with

full power and ground planes board to guide layout and

aid device evaluation. Following this layout configuration

provides

optimum

performance

and

thermal

characteristics for the device. For best results, follow the

steps and recommended routing rules below.

Recommended Routing / Layout Rules

 Do not run analog and digital signals in parallel.

 Use separate analog and digital power planes to

supply power.

 Traces must run on top of the ground plane.

 No trace should run over ground/power splits.

 Avoid routing at 90-degree angles.

 Minimize clock and video data trace length

differences.

 Include 10μF and 0.1μF ceramic power supply

bypass capacitors.

 Place the 0.1μF capacitor within 2.54mm (0.1in)

of the device power pin.

 Place the 10μF capacitor within 19.05mm (0.75in)

of the device power pin.

 For multi-layer boards, use a large ground plane to

help dissipate heat.

 For two-layer boards, use a ground plane that

extends beyond the device body at least 12.7mm

(0.5in) on all sides. Include a metal paddle under

the device on the top layer.

 Minimize all trace lengths to reduce series

inductance.

Output Considerations

The outputs are DC offset from the input by 150mV;

therefore, VOUT = 2 • VIN DC + 150mV. This offset is

required for optimal performance from the output driver

and is held at the minimum value to decrease the

standing DC current into the load. Since the FMS6404

has a 2 x (6dB) gain, the output is typically connected

via a 75Ω-series back-matching resistor, followed by the

75Ω video cable. Due to the inherent divide-by-two of

this configuration, the blanking level at the load of the

video signal is always less than 1V. When AC-coupling

the output, ensure that the coupling capacitor passes

the lowest frequency content in the video signal and that

line time distortion (video tilt) is kept as low as possible.

The selection of the coupling capacitor is a function of

the subsequent circuit input impedance and the leakage

current of the input being driven. To obtain the highest

quality output video signal, the series termination

resistor must be placed as close to the device output pin

possible.

This

greatly

reduces

the

parasitic

capacitance and inductance effect on the output driver.

The distance from the device pin to the series termination

resistor should be no greater than 2.54mm (0.1in).

Figure 14. Termination Resistor Placement

Thermal Considerations

Since the interior of most systems, such as set-top

boxes,

TVs,

and

DVD

players;

+70ºC;

consideration must be given to providing an adequate

heat sink for the device package for maximum heat

dissipation. When designing a system board, determine

how much power each device dissipates. Ensure that

devices of high power are not placed in the same

location, such as directly above (top plane) or below

(bottom plane) each other on the PCB.

PCB Thermal Layout Considerations

 Understand the system power requirements and

environmental conditions.

 Maximize thermal performance of the PCB.

 Consider using 70μm of copper for high-power

designs.

 Make the PCB as thin as possible by reducing

FR4 thickness.

 Use vias in power pad to tie adjacent layers

together.

 Remember that baseline temperature is a function

of board area, not copper thickness.

 Modeling techniques provide a first-order

approximation.

FMS6404CSX 데이터시트(PDF) 8 Page - ON Semiconductor

FMS6404CSX 데이터시트(HTML) 8 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11

데이터시트 다운로드

링크 URL