| 전자부품 데이터시트 검색엔진 |
|
VDP3108B 데이터시트(PDF) 18 Page - Micronas |
|
|
|||||||||||||||||||||||||||||
VDP3108B 데이터시트(HTML) 18 Page - Micronas |
|
18 / 72 page ![]() PRELIMINARY DATA SHEET VDP 31xxB 18 Micronas 2.8.8. Chroma Transient Improvement The intention of this block is to enhance the chroma resolution. A correction signal is calculated by differenti- ation of the color difference signals. The differentiation can be selected according to the signal bandwidth, e.g. for PAL/NTSC/SECAM or digital component signals, respectively. The amplitude of the correction signal is adjustable. Small noise amplitudes in the correction sig- nal are suppressed by an adjustable coring circuit. To eliminate ‘wrong colors’, which are caused by over and undershoots at the chroma transition, the sharpened chroma signals are limited to a proper value automati- cally. Fig. 2–18: Digital Color Transient Improvement t t t Cr out Cb out Ampl. Cr in Cb in a) b) c) a) Cr Cb input of DTI b) Cr Cb input )Correction signal c) sharpened and limited Cr Cb 2.8.9. Inverse Matrix A 6-multiplier matrix transcodes the Cr and Cb signals to R–Y, B–Y, and G–Y. The multipliers are also used to adjust color saturation in the range of 0 to 2. The coeffi- cients are signed and have a resolution of 9 bits. There are separate matrix coefficients for main and side pic- tures. The matrix computes: R–Y +MR1*Cb)MR2*Cr G–Y +MG1*Cb)MG2*Cr B–Y +MB1*Cb)MB2*Cr The initialization values for the matrix are computed from the standard ITUR (CCIR) matrix: R G B + 1 1 1 0 * 0.345 1.773 1.402 * 0.713 0 Y Cb Cr For a contrast setting of CTM +32, the matrix values are scaled by a factor of 64, see also table 3–1. 2.8.10. RGB Processing After adding the post-processed luma, the digital RGB signals are limited to 10 bits. Three multipliers are used to digitally adjust the white drive. Using the same multi- pliers an average beam current limiter is implemented. See also section 2.9.1. ‘CRT Measurement and Con- trol’. 2.8.11. OSD Color Lookup Table The VDP 31xxB has five input lines for an OSD signal. This signal forms a 5-bit address for a color look-up table (CLUT). The CLUT is a memory with 32 words where each word holds a RGB value. Bits 0 to 3 (bit 4 +0) form the addresses for the ROM part of the OSD, which generates full RGB signals (bit 0 to 2) and half-contrast RGB signals (bit 3). Bit 4 addresses the RAM part of the OSD with 16 freely programmable colors, addressable with bit 0 to 3. The programming is done via the I2C-bus. The amplitude of the CLUT output signals can be ad- justed separately for R, G and B via the I2C-bus. The switchover between video RGB and OSD RGB is done via the Priority bus. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |