SC68C752B datasheet(30/49 Pages) PHILIPS

30 / 49 page

SC68C752B_3

Product data sheet

Rev. 03 — 29 November 2005

30 of 49

Philips Semiconductors

SC68C752B

5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs

7.10 Enhanced Feature Register (EFR)

This 8-bit register enables or disables the enhanced features of the UART. Table 20 shows

the Enhanced Feature Register bit settings.

7.11 Divisor latches (DLL, DLH)

These are two 8-bit registers which store the 16-bit divisor for generation of the baud clock

in the baud rate generator. DLH stores the most signiﬁcant part of the divisor. DLL stores

the least signiﬁcant part of the divisor.

Note that DLL and DLH can only be written to before Sleep mode is enabled, that is,

before IER[4] is set.

7.12 Transmission Control Register (TCR)

This 8-bit register is used to store the RX FIFO threshold levels to stop/start transmission

during hardware/software ﬂow control. Table 21 shows transmission control register bit

settings.

TCR trigger levels are available from 0 bytes to 60 bytes with a granularity of four.

Table 20:

Enhanced Feature Register bits description

Bit

Symbol

Description

EFR[7]

CTS ﬂow control enable.

logic 0 = CTS ﬂow control is disabled (normal default condition)

logic 1 = CTS ﬂow control is enabled. Transmission will stop when a HIGH

signal is detected on the CTS pin.

EFR[6]

RTS ﬂow control enable.

logic 0 = RTS ﬂow control is disabled (normal default condition)

logic 1 = RTS ﬂow control is enabled. The RTS pin goes HIGH when the

receiver FIFO halt trigger level TCR[3:0] is reached, and goes LOW when the

receiver FIFO resume transmission trigger level TCR[7:4] is reached.

EFR[5]

Special character detect.

logic 0 = special character detect disabled (normal default condition)

logic 1 = special character detect enabled. Received data is compared with

Xoff2 data. If a match occurs, the received data is transferred to FIFO and

IIR[4] is set to a logical 1 to indicate a special character has been detected.

EFR[4]

Enhanced functions enable bit.

logic 0 = disables enhanced functions and writing to IER[7:4], FCR[5:4],

MCR[7:5]

logic 1 = enables the enhanced function IER[7:4], FCR[5:4], and MCR[7:5]

can be modiﬁed, that is, this bit is therefore a write enable

3:0

EFR[3:0]

Combinations of software ﬂow control can be selected by programming these

bits. See Table 4 “Software ﬂow control options (EFR[0:3])” on page 10.

Table 21:

Transmission Control Register bits description

Bit

Symbol

Description

7:4

TCR[7:4]

RX FIFO trigger level to resume transmission (0 bytes to 60 bytes).

3:0

TCR[3:0]

RX FIFO trigger level to halt transmission (0 bytes to 60 bytes).

SC68C752B 데이터시트(PDF) 30 Page - NXP Semiconductors

SC68C752B 데이터시트(HTML) 30 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

데이터시트 다운로드

링크 URL