TUSB8044AI datasheet(15/63 Pages) TI1

15 / 63 page

TUSB8044A

www.ti.com

SLLSF92 – FEBRUARY 2019

Product Folder Links: TUSB8044A

Submit Documentation Feedback

8.3 Feature Description

8.3.1 Battery Charging Features

The TUSB8044A provides support for USB Battery Charging (BC1.2) and custom charging. Battery charging

support may be enabled on a per port basis through the REG_6h(batEn[3:0]) or the BATEN[4:1] pins.

USB Battery charging support includes both Charging Downstream Port (CDP) and Dedicated Charging Port

(DCP) modes. The DCP mode is compliant with the Chinese Telecommunications Industry Standard YD/T 1591-

2009. CDP is enabled when the upstream port has detected valid VBUS, configured, and host sets port power.

When the upstream port is not connected and battery charging support is enabled, the TUSB8044A will enable

DCP mode once all other battery modes such as ACPx have failed or are disabled.

In addition to USB Battery charging (BC1.2), the TUSB8044A supports custom charging indications: Divider

Charging (ACP3, ACP2, ACP1 modes), and Galaxy compatible charging. These custom charging modes are

only supported when upstream port is unconnected and AUTOMODE is enabled. AUTOMODE can be enabled

either thru AUTOENz pin or from Reg_0Ah bit 1 (autoModeEnz) . When in AUTOMODE and upstream port is

disconnected, the port will automatically transition from ACP mode to the DCP mode depending on the portable

device connected. The divided mode places a fixed DC voltage on the ports DP and DM signals which allows

some devices to identify the capabilities of the charger. The default divider mode indicates support for up to 10W

(ACP3). The divider mode can be configured to report a lower-current setting (up to 5 W) through REG_0Ah

(HiCurAcpModeEn).

When the upstream port is not connected and battery charging support is enabled for a port, the TUSB8044A

drives the port power enable active. If AUTOMODE is disabled, then DCP mode is used. If AUTOMODE is

enabled and fully automatic mode is disabled (FullAutoEn bit is cleared (Reg_25h Bit 0) or FULLAUTOz pin = 0),

then TUSB8044A will start with highest enabled divider current mode (ACPx). The TUSB8044A will remain in

highest current mode as long as a pull-up is not detected on DP pin. If an pull-up is detected on DP pin, then

TUSB8044A will drive the port power enable inactive and switch to Galaxy mode, if enabled, or to DCP mode if

Galaxy mode is disabled. The TUSB8044A will again drive the port power enable active. The TUSB8044A will

remain in Galaxy mode as long as no pull-up is detected on DP pin. If an pull-up is detected on DP pin, then

TUSB8044A will drive the port power enable inactive and transition to DCP mode. The TUSB8044A will again

drive the port power enable active. In DCP mode, the TUSB8044A will look for a pull-up detected on DP pin or

RxVdat. If a pull-up or RxVdat is detected on DP, the TUSB8044A will remain in DCP mode. If no pull-up or

RxVdat is detected on DP pin after 2 seconds, the TUSB8044A will drive the port power enable inactive and

transition back to ACPx mode. This sequence will repeat until upstream port is connected.

When Automatic mode is enabled and full automatic mode is enabled (FullAutoEn Reg_25h bit 0 is set or

FULLAUTOz pin = 1), TUSB8044A will perform same sequence described in previous paragraph with the

addition of attempting all supported ACPx modes before sequencing to Galaxy Mode (if enabled) or DCP mode.

The supported battery charging modes when TUSB8044A configured for SMBus or external EEPROM is detailed

in Battery Charging Modes with SMBus/EEPROM Table.

The supported battery charging modes when TUSB8044A configured for I2C but without an external EEPROM is

determined by the sampled state of the pins. These modes are detailed in Battery Charging Modes without

EEPROM Table.

TUSB8044AI 데이터시트(PDF) 15 Page - Texas Instruments

TUSB8044AI 데이터시트(HTML) 15 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

데이터시트 다운로드

링크 URL