ZPSD301-B-90LI datasheet(27/85 Pages) STMICROELECTRONICS

27 / 85 page

PSD3XX Family

12.0

Control Signals

(cont.)

12.6 Reset Input

This is an asynchronous input to initialize the PSD device.

Refer to tables 8A and 8B for information on device status during and after reset.

The standard-voltage PSD3XX and ZPSD3XX (non-V) devices require a reset input that

is asserted for at least 100 nsec. The PSD will be functional immediately after reset is

de-asserted. For these standard-voltage devices, the polarity of the reset input signal is

programmable using PSDsoft (active-high or active-low), to match the functionality of your

MCU reset.

Note: It is not recommended to drive the reset input of the MCU and the reset input of the

PSD with a simple RC circuit between power on ground. The input threshold of the MCU

and the PSD devices may differ, causing the devices to enter and exit reset at different

times because of slow ramping of the signal. This may result in the PSD not being

operational when accessed by the MCU. It is recommended to drive both devices actively.

A supervisory device or a gate with hysteresis is recommended.

For low-voltage ZPSD3XXV devices only, the reset input must be asserted for at least

500 nsec. The ZPSD3XXV will not be functional for an additional 500 nsec after reset is

de-asserted (see Figure 8). These low voltage ZPSD3XXV devices must use an active-low

polarity signal for reset. Unlike the standard PSDs, the reset polarity for the ZPSD3XXV is

not programmable. If your MCU operates with an active high reset, you must invert this

signal before driving the ZPSD3XXV reset input.

You must design your system to ensure that the PSD comes out of reset and the PSD is

active before the MCU makes its first access to PSD memory. Depending on the

characteristics and speed of your MCU, a delay between the PSD reset and the MCU reset

may be needed.

Signal State Just

Signal State

After Reset

Port

Configured Mode of Operation

During Reset

(Note 1)

AD0/A0-

All

Input (Hi-Z)

MCU address

AD15/A15

and/or data

MCU I/O

Input (Hi-Z)

Tracking

Input (Hi-Z)

Active Track

Port Pins

AD0/A0-AD7/A7

Mode

PA0-PA7

PSD3XX,

Logic 0

MCU address

Latched Address Out

ZPSD3XX

ZPSD3XXV

Hi-Z

MCU address

MCU I/O

Input (Hi-Z

Input (Hi-Z)

Chip Select Outputs,

PSD3XX,

Logic 1

Per CS equations

Port Pins

CS0-CS7, CMOS

ZPSD3XX

PB0-PB7

ZPSD3XXV

Hi-Z

Per CS equations

Chip Select Outputs,

PSD3XX,

Hi-Z

Per CS equations

CS0-CS7, Open Drain

ZPSD3XX

ZPSD3XXV

Hi-Z

Per CS equations

Address or Logic Inputs, A16-A18

Input (Hi-Z)

Port Pins

Chip Select Outputs,

PSD3XX,

Logic 1

Per CS equations

PC0-PC2

CS8-CS10, CMOS

ZPSD3XX

ZPSD3XXV

Hi-Z

Per CS equations

Table 8A. External PSD Signal States During and Just After Reset

NOTE: 1. Signal is valid immediately after reset for PSD3XX and ZPSD3XX devices. ZPSD3XXV devices need an

additional 500 nsec after reset before signal is valid.

ZPSD301-B-90LI 데이터시트(PDF) 27 Page - STMicroelectronics

ZPSD301-B-90LI 데이터시트(HTML) 27 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85

데이터시트 다운로드

링크 URL