ADE1202 datasheet(34/42 Pages) AD

34 / 42 page

ADE1202

Data Sheet

Rev. 0 | Page 34 of 42

BINARY CHANNEL CONTROL REGISTER

Address: 0x002, Reset: 0x3610, Name: BIN_CTRL

Binary channel and warning controls for decimation and filter modes.

Table 20. Bit Descriptions for BIN_CTRL

Bits

Bit Name

Description

Reset

Access

RESERVED

Reserved.

0x0

LOAD_STANDBY_MODE

Load Standby Mode. In load standby mode the binary channel monitors the load

standby current instead of the ADC voltage values.

0x0

R/W

[13:12]

WARNC_MODE

Comparator Mode.

0x3

R/W

0: hysteretic mode. When the ADC output is greater than the high threshold level

of the comparator, the output is set high. The output is set low when the ADC

output drops below the low threshold level.

1: midrange mode. When the ADC output is less than the high threshold level and

greater than the low threshold level, the comparator output is set high.

10: GT. When the ADC output is greater than the high threshold level, the

comparator output is set high.

11: LT mode. When the ADC output is lower than or equal to the high threshold

level, the comparator output is set high.

[11:10]

WARNB_MODE

Comparator Mode.

0x1

R/W

0: hysteretic mode. When the ADC output is greater than the high threshold level

of the comparator, the output is set high. The output is set low when the ADC

output drops below the low threshold level.

1: midrange mode. When the ADC output is less than the high threshold level and

greater than the low threshold level, the comparator output is set high.

10: GT mode. When the ADC output is greater than the high threshold level, the

comparator output is set high.

11: LT mode. When the ADC output is lower than or equal to the high threshold

level, the comparator output is set high.

[9:8]

WARNA_MODE

Comparator Mode.

0x2

R/W

0: hysteretic mode. When the ADC output is greater than the high threshold level

of the comparator, the output is set high. The output is set low when the ADC

output drops below the low threshold level.

1: midrange mode. When the ADC output is less than the high threshold level and

greater than the low threshold level, the comparator output is set high.

10: GT mode. When the ADC output is greater than the high threshold level, the

comparator output is set high.

11: LT mode. When the ADC output is lower than or equal to the high threshold

level, the comparator output is set high.

[7:6]

BIN_MODE

Comparator Mode.

0x0

R/W

0: hysteretic mode. When the ADC output is greater than the high threshold level

of the comparator, the output is set high. The output is set low when the ADC

output drops below the low threshold level.

1: midrange mode. When the ADC output is less than the high threshold level and

greater than the low threshold level, the comparator output is set high.

10: GT mode. When the ADC output is greater than the high threshold level, the

comparator output is set high.

11: LT mode. When the ADC output is lower than or equal to the high threshold

level, the comparator output is set high.

[5:4]

INVALID_MODE

Invalid Mode. This bit field selects the value driven onto DOUTx in invalid mode.

0x1

R/W

00: DOUTx equals the FORCEVAL bit value.

01: DOUTx equals the binary filter output.

10: DOUTx toggles value on entering invalid mode.

11: DOUTx holds current value.

FORCEVAL

DOUTx Value During Invalid Mode.

0x0

R/W

ADE1202 데이터시트(PDF) 34 Page - Analog Devices

ADE1202 데이터시트(HTML) 34 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

데이터시트 다운로드

링크 URL