ADM2461EBRWZ-R7 datasheet(6/21 Pages) AD

6 / 21 page

ADM2461E/ADM2463E

Data Sheet

Rev. 0 | Page 6 of 21

PACKAGE CHARACTERISTICS

Table 3.

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Resistance (Input to Output)1

RI-O

1013

Capacitance (Input to Output)1

CI-O

2.2

Test frequency = 1 MHz

Input Capacitance2

3.0

1 The device is considered a 2-terminal device. Short together Pin 1 through Pin 8 and short together Pin 9 through Pin 16 to set the device up as a 2-terminal device during testing.

2 Input capacitance is from any input data pin to ground.

REGULATORY INFORMATION

For additional information, see www.analog.com/icouplersafety.

Table 4. ADM2461E/ADM2463E Approvals

UL (Pending)

CSA (Pending)

VDE (Pending)

CQC (Pending)

Recognized Under UL 1577

Component Recognition

Protection1

Approved under CSA Component

Acceptance Notice 5A

To be certified under

DIN V VDE 0884-112

Certified under CQC11-

471543-2012

Single Protection, 5700 V rms

CSA 60950-1-07+A1+A2 and

IEC 60950-1, second edition, +A1+A2

Basic insulation

GB4943.1-2011

Basic insulation at 800 V rms (1131 V peak)

Working voltage (VIOWM) = 875 V rms

Basic insulation at 800 V rms

(1131 V peak)

Reinforced insulation at 400 V rms

(565 V peak)

Repetitive maximum voltage (VIORM) = 1237 V peak

Reinforced insulation at

400 V rms (565 V peak)

CSA 62368-1-14, EN 62368-1:2014/A11:2017

and IEC 62368-1: 2014 second edition

Surge isolation voltage (VIOSM) = 10 kV peak

Basic insulation at 800 V rms

(1131 V peak)

Highest allowable overvoltage (VIOTM) = 8000 V peak

Reinforced insulation at 400 V rms

(565 V peak)

Reinforced insulation

IEC 60601-1 Edition 3.1

VIOWM = 750 V rms

1 means of patient protection

(1 MOPP), 400 V rms (565 V peak)

VIORM = 1060 V peak

2 MOPP, 250 V rms (353 V peak)

VIOSM = 6.25 kV peak

1 MOPP or 2 MOPP, 400 V rms (565 V peak)

VIOTM = 8000 V peak

CSA 61010-1-12 and IEC 61010-1 third edition

Basic insulation at 300 V rms mains, 800 V rms

(1131 V peak) from secondary circuit

Reinforced insulation at 300 V rms mains,

400 V rms (565 V peak) from secondary circuit

File (pending)

1 In accordance with UL 1577, each ADM2461E/ADM2463E is proof tested by applying an insulation test voltage ≥ 6840 V rms for 1 sec.

2 In accordance with DIN V VDE 0884-11, each ADM2461E/ADM2463E is proof tested by applying an insulation test voltage ≥ 2320 V peak for 1 sec (partial discharge

detection limit = 5 pC).

INSULATION AND SAFETY RELATED SPECIFICATIONS

Table 5. Critical Safety Related Dimensions and Material Properties

Parameter

Symbol

Value

Unit

Test Conditions/Comments

Rated Dielectric Insulation Voltage

5700

V rms

1-minute duration

Minimum External Air Gap (Clearance)

L(I01)

8.3

Measured from input terminals to output terminals, shortest

distance through air

Minimum External Tracking (Creepage)

L(I02)

8.3

Measured from input terminals to output terminals, shortest

distance along body

Minimum Clearance in the Plane of the Printed

Circuit Board (PCB Clearance)

L (PCB)

8.1

Measured from input terminals to output terminals, shortest

distance through air, line of sight, in the PCB mounting plane

Minimum Internal Gap (Internal Clearance)

μm min

Insulation distance through insulation

Tracking Resistance (Comparative Tracking Index)

CTI

>600

DIN IEC 112/VDE 0303 Part 1

Material Group

Material Group (DIN VDE 0110: 1989-01, Table 1)

ADM2461EBRWZ-R7 데이터시트(PDF) 6 Page - Analog Devices

ADM2461EBRWZ-R7 데이터시트(HTML) 6 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

데이터시트 다운로드

링크 URL