| 전자부품 데이터시트 검색엔진 |
|
MICRF405 데이터시트(PDF) 12 Page - Micrel Semiconductor |
|
|
|||||||||||||||||||||||||||||
MICRF405 데이터시트(HTML) 12 Page - Micrel Semiconductor |
|
12 / 46 page ![]() Micrel MICRF405 April 2006 12 M9999-041906 (408) 955-1690 Writing to n Registers having Non-Incremental Addresses Registers with non-incremental addresses can be written to in one write-sequence as well. Example of non-incremental addresses: “0,1,3”. However, this requires more overhead, and the user should consider the possibility to make a “continuous” update, for example, by writing to “0,1,2,3” (writing the present value of “2” into “2”). The simplest firmware is achieved by always writing to all registers. Refer to previous sections. This write-sequence is divided into several sub- parts: • Disable the generation of load-signals by clearing bit “load_en” (D0 in ControlRegister0) • Repeat for each group of register having incremental addresses: - Bring SEN active - Enter first address for this group, R/W bit and values - Bring SEN inactive • Finally, enable and make a load-signal by setting “load_en” Refer to the previous sections for how to write to 1 or n (with incremental addresses) registers in the MICRF405. Reading from the Control Registers in MICRF405 The “read-sequence” is: 1. Enter address and R/W bit 2. Change direction of SIO line 3. Read out a number of octets and change SIO direction back again. It is possible to read all, 1 or n registers. The address to read from (or the first address to read from) can be any valid address (0-29). Reading is not destructive, i.e., values are not changed. The SIO line is output from the MICRF405 (input to user) for a part of the read-sequence. Refer to procedure description below. A read-sequence is described for reading n registers, where n is number 1-30. SEN SIO SCK Register address Data read from register Internal load pulse generated here A6 A5 A4 A3 A2 A1 A0 R/W D7 D6D5 D4 D3 D2 D1 D0 SIO INPUT SIO OUTPUT SAMPLE TIME Figure 4. Reading from a Control Register. In Figure 4 above, 1 register is read. The address is A6, A5, … A0. A6 = MSB. The data read out is D7, D6, …D0. The value of the R/W bit is always “1” for reading. • Bring SEN low • Enter address to read from (or the first address to read from) (7 bits) and • The R/W bit = 1 to enable reading • Make the SIO line an input to the user (set pin in tristate) • Read n octets. The first rising edge of SLK will set the SIO as an output from the MICRF405. The 405 will change the SIO line at positive edges of SCK. The user should read the SIO line at the negative edges. • Make the SIO line an output from the user again. Reading from the Interrupt Register If any of the interrupts, Vc_HI, Vc_LO or Low_Batt, is set the SRV pin will go high. Read the interrupt register, address 24, to see which interrupts are flagged. It is possible to read this register at all times, for instance, to read the tuned VCO_FREQ setting which is also stored at the same address. When rising SEN after haveing read the register, the internal load pulse will then clear all interrupt flags. To keep the flags when reading it, it is therefore necessary to set LOAD_en=0 before hand. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |