HT48C10 datasheet(25/59 Pages) HOLTEK

25 / 59 page

Of the HT48C50/HT48C70, the timer/event

counter is comprised by two counters, i.e.,

timer/event counter 0 and timer/event counter

1. There are three registers related to the

timer/event counter 0, namely TMR0H (0CH),

TMR0L (0DH), and TMR0C (0EH). Writing

TMR0L only writes the data into a low byte

buffer, but writing TMR0H writes the data

along with the contents of the low byte buffer

into the timer/event counter 0 preload register

(16-bit). The timer/event counter 0 preload reg-

ister is changed by writing the TMR0H opera-

tions, and writing TMR0L keeps the timer/

event counter 0 preload register unaltered.

Also, reading the TMR0H latches the TMR0L

into the low byte buffer in order to avoid the

false timing problem. Then, reading the TMR0L

will return the contents of the low byte buffer.

In other words, the low byte of the timer/event

counter 0 cannot be read directly. Instead it has

to read the TMR0H first in order to make the

low byte contents of the timer/event counter 0

latched into the buffer. On the other hand, there

are also thre e registe rs relate d to the

timer/event counter 1, namely TMR1H (0FH),

TMR1L (10H), and TMR1C (11H). The timer/

event counter 1 operates in the same manner as

the timer/event counter 0.

The TMR0C is a timer/event counter 0 control

tions. The timer/event counter 1 has the same

options as the timer/event counter 0 and is de-

fined by TMR1C.

The timer/event counter control registers of the

four microcontrollers are all used to define the

operation mode, counting enable or disable, and

active edge.

The TM0 and TM1 bits define the operation

mode. The event count mode is used to count

external events, which means that the clock

source comes from an external pin TMR of the

HT48C10/HT48C30 or TMR0/TMR1 of the

HT48C50/HT48C70. The timer mode functions

as a normal timer with the clock source coming

from the instruction clock. The pulse width

measurement mode can be used to count the

high or low level duration of the external signal

TMR of the HT48C10/HT48C30 or TMR0/TMR

1 of the HT48C50/HT48C70. The counting is

based on the instruction clock.

In the event count or timer mode, once the

timer/event counter starts counting, it will count

from the current contents in the timer/event

counter to FFH of the HT48C10/HT48C30/

HT48C50 (TMR1) or to FFFFH of the HT48C50

(TMR0)/HT48C70. If an overflow occurs, the

counter is reloaded from the timer/ event counter

preload register and generates the corresponding

interrupt request flag TF (bit 5 of INTC) of the

HT48C10/HT48C30 or T0F/T1F (bit 5/6 of INTC)

of the HT48C50/ HT48C70 at the same time.

Label

Bits

Function

—

0~2

Unused bits, read as “0”

To define TMR0/TMR1 active edge of the timer/event counter

(0= active on low to high; 1= active on high to low)

TON

To enable/disable timer counting

(0= disabled; 1= enabled)

—

Unused bits, read as “0”

TM0

TM1

To define the operating mode

01= Event count mode (external clock)

10= Timer mode (internal clock)

11= Pulse width measurement mode

00= Unused

TMR0C/TMR1C register

HT48CXX/HT48RXX

25th May ’99

HT48C10 데이터시트(PDF) 25 Page - Holtek Semiconductor Inc

HT48C10 데이터시트(HTML) 25 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

데이터시트 다운로드

링크 URL