UPSD3422EB40U6 datasheet(103/300 Pages) STMICROELECTRONICS

103 / 300 page

Obsolete

Product(s)

- Obsolete

Product(s)

Obsolete

Product(s)

- Obsolete

Product(s)

UPSD3422, UPSD3433, UPSD3434, UPSD3454

Standard 8032 timer/counters

103/300

20.6.3

Baud rate generator mode

The RCLK and/or TCLK Bits in the SFR T2CON allow the transmit and receive baud rates

on serial port UART0 to be derived from either Timer 1 or Timer 2. Figure 29 on page 106

illustrates Baud rate generator mode.

When TCLK = 0, Timer 1 is used as UART0’s transmit baud generator. When TCLK = 1,

Timer 2 will be the transmit baud generator. RCLK has the same effect for UART0’s receive

baud rate. With these two bits, UART0 can have different receive and transmit baud rates -

one generated by Timer 1, the other by Timer 2.

Note:

Bits RCLK1 and TCLK1 in the SFR named PCON (see Section Table 33.: PCON: power

control register (SFR 87h, reset value 00h) on page 74) have identical functions as RCLK

and TCLK but they apply to UART1 instead. For simplicity in the following discussions about

baud rate generation, no suffix will be used when referring to SFR registers and bits related

to UART0 or UART1, since each UART interface has identical operation. Example, TCLK or

TCLK1 will be referred to as just TCLK.

The Baud rate generator mode is similar to the Auto-reload mode, in that a roll over in TH2

causes the Timer 2 registers, TH2 and TL2, to be reloaded with the 16-bit value in registers

RCAP2H and RCAP2L, which are preset with firmware.

The baud rates in UART Modes 1 and 3 are determined by Timer 2’s overflow rate as

follows:

UART Mode 1,3 Baud Rate =Timer 2 Overflow Rate / 16

The timer can be configured for either “timer” or “counter” operation. In the most typical

applications, it is configured for “timer” operation (C/T2 = 0). “Timer” operation is a little

different for Timer 2 when it's being used as a baud rate generator. In this case, the baud

rate is given by the formula:

UART Mode 1,3 Baud Rate =fOSC/(32 x [65536 – [RCAP2H, RCAP2L]))

where [RCAP2H, RCAP2L] is the content of the SFRs RCAP2H and RCAP2L taken as a

16-bit unsigned integer.

A roll-over in TH2 does not set TF2, and will not generate an interrupt. Therefore, the Timer

Interrupt does not have to be disabled when Timer 2 is in the Baud rate generator mode.

If EXEN2 is set, a 1-to-0 transition on pin T2X will set the Timer 2 interrupt flag EXF2, but

will not cause a reload from RCAP2H and RCAP2L to TH2 and TL2. Thus when Timer 2 is

Baud rate

generator

No overflow interrupt request

(TF2)

fOSC/2

–

↓

Extra Interrupt on pin T2X, sets

TF2

Off

Timer 2 stops

–

↓= falling edge.

Table 62.

Timer/counter 2 operating modes (continued)

Mode

Bits in T2CON SFR

T2X

(1)

Remarks

Input clock

RCLK

TCLK

CP/

RL2

TR2 EXEN2

Timer,

internal

Counter,

external

(Pin T2,

P1.0)

Obsolete

Product(s)

- Obsolete

Product(s)

UPSD3422EB40U6 데이터시트(PDF) 103 Page - STMicroelectronics

UPSD3422EB40U6 데이터시트(HTML) 103 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL