HC5503PRC

FN4806 Rev.3.00

Page 11 of 11

June 2004

Quad Flat No-Lead Plastic Package (QFN)

Micro Lead Frame Plastic Package (MLFP)

INDEX

D1/2

D1

D/2

D

E1/2

E/2

E

A

2X

0.15

B

C

0.10

B

A

MC

A

N

SEATING PLANE

N

6

3

2

2

3

e

1

1

0.08

FOR ODD TERMINAL/SIDE

FOR EVEN TERMINAL/SIDE

C

C

SECTION "C-C"

NX b

A1

C

2X

C

0.15

0.15

2X

B

REF.

(Nd-1)Xe

(Ne-1)Xe

REF.

5

A1

4X P

A

C

C

4X P

B

2X

A

C

0.15

A2

A3

D2

D2

E2

E2/2

TERMINAL TIP

SIDE VIEW

TOP VIEW

7

BOTTOM VIEW

7

5

CL

CL

e

e

E1

2

NX k

NX b

8

NX L

8

8

9

AREA

9

4X

0.10 C

/ /

9

(DATUM B)

(DATUM A)

AREA

INDEX

6

AREA

N

9

CORNER

OPTION 4X

L1

L

10

L1

L

10

L32.7x7

32 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE

(COMPLIANT TO JEDEC MO-220VKKC ISSUE C)

SYMBOL

MILLIMETERS

NOTES

MIN

TYP

MAX

A

0.80

0.90

1.00

-

A1

-

-

0.05

-

A2

-

-

1.00

9

A3

0.20 REF

9

b

0.23

0.28

0.38

5, 8

D

7.00 BSC

-

D1

6.75 BSC

9

D2

4.55

4.70

4.85

7, 8

E

7.00 BSC

-

E1

6.75 BSC

9

E2

4.55

4.70

4.85

7, 8

e

0.65 BSC

-

k

0.25

---

L

0.50

0.60

0.75

8

L1

-

-

0.15

10

N32

2

Nd

8

3

Ne

8

3

P-

-

0.60

9



--

12

9

Rev. 4 8/03

NOTES:

1. Dimensioning and tolerancing conform to ASME Y14.5-1994.

2. N is the number of terminals.

3. Nd and Ne refer to the number of terminals on each D and E.

4. All dimensions are in millimeters. Angles are in degrees.

5. Dimension b applies to the metallized terminal and is measured

between 0.15mm and 0.30mm from the terminal tip.

6. The configuration of the pin #1 identifier is optional, but must be

located within the zone indicated. The pin #1 identifier may be

either a mold or mark feature.

7. Dimensions D2 and E2 are for the exposed pads which provide

improved electrical and thermal performance.

8. Nominal dimensions are provided to assist with PCB Land

Pattern Design efforts, see Intersil Technical Brief TB389.

9. Features and dimensions A2, A3, D1, E1, P &

 are present

when Anvil singulation method is used and not present for saw

singulation.

10. Depending on the method of lead termination at the edge of the

package, a maximum 0.15mm pull back (L1) maybe present. L

minus L1 to be equal to or greater than 0.3mm.