ISL8200MM

FN7690 Rev 2.00

Page 7 of 24

Mar 15, 2013

Absolute Maximum Ratings

Thermal Information

Input Voltage, PVIN, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +27V

Driver Bias Voltage, PVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V

Signal Bias Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V

BOOT/UGATE Voltage, VBOOT . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to +36V

Phase Voltage, VPHASE . . . . . . . . . . . . . . . . . . . VBOOT - 7V to VBOOT + 0.3V

BOOT to PHASE Voltage,

VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V

Input, Output or I/O Voltage . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V

ESD Rating

Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . 2kV

Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . 200V

Charge Device Model (Tested per JESD22-C101C). . . . . . . . . . . . . . . 1kV

Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA

Thermal Resistance (Typical)

JA (°C/W) JC (°C/W)

QFN Package (Notes 3, 4) . . . . . . . . . . . . . .

13

2.0

Maximum Storage Temperature Range . . . . . . . . . . . . . -55°C to +150°C

Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

Recommended Operating Conditions

Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 20V

Input Voltage, PVIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 20V

Driver Bias Voltage, PVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.6V

Signal Bias Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.6V

Boot to Phase Voltage (Overcharged),

VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <6V

Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product

reliability and result in failures not covered by warranty.

NOTES:

3.

JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. (i.e., 4-layer

type without thermal vias – see tech brief TB379) per JEDEC standards except that the top and bottom layers assume solid planes.

4. For

JC, case temperature location is the center of the package underside.

Electrical Specifications

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

TYP

(Note 5)

MAX

UNITS

VCC SUPPLY CURRENT

Nominal Supply VIN Current

IQ_VIN

PVIN = VIN = 20V; No Load; FSW = 700kHz

36

mA

Nominal Supply VIN Current

IQ_VIN

PVIN = VIN = 4.5V; No Load; FSW = 700kHz

27

mA

Shutdown Supply VCC Current

IVCC

EN = 0V, VCC = 2.97V

9

mA

INTERNAL LINEAR REGULATOR (Note 6)

Maximum Current

IPVCC

PVCC = 4V TO 5.6V

320

mA

PVCC = 3V TO 4V

150

mA

Saturated Equivalent Impedance

RLDO

P-Channel MOSFET (VIN = 5V)

1

Ω

POWER-ON RESET (Note 6)

Rising VCC Threshold

2.85

(Note 8)

V

Falling VCC Threshold

2.65

(Note 8)

V

Rising PVCC Threshold

2.85

(Note 8)

V

Falling PVCC Threshold

2.65

(Note 8)

V

System Soft-start Delay

tSS_DLY

After PLL, VCC, and PVCC PORs, and EN above

their thresholds

384

Cycles

ENABLE (Note 6)

Turn-On Threshold Voltage

(Note 8)

0.8

(Note 8)

V

Hysteresis Sink Current

IEN_HYS

(Note 8)

30

(Note 8)

μA

Undervoltage Lockout Hysteresis

VEN_HYS

VEN_RTH = 10.6V; VEN_FTH = 9V

RUP = 53.6kΩ, RDOWN = 5.23kΩ

1.6

V

Sink Current

IEN_SINK

VEN = 1V

(Note 8)

mA

Sink Impedance

REN_SINK VEN = 1V

(Note 8)

Ω