| 전자부품 데이터시트 검색엔진 |
|
AT43USB353M 데이터시트(PDF) 25 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
AT43USB353M 데이터시트(HTML) 25 Page - ATMEL Corporation |
|
25 / 95 page ![]() 25 AT43USB353M 3307B–USB–4/04 MCU Control Register – MCUCR • Bit 7, 6 – Res: Reserved Bits • Bit 5 – SE: Sleep Enable The SE bit must be set (1) to make the MCU enter the sleep mode when the SLEEP instruc- tion is executed. To avoid the MCU entering the sleep mode, unless it is the programmer's purpose, it is recommended to set the Sleep Enable SE bit just before the execution of the SLEEP instruction. • Bit 4 – SM: Sleep Mode This bit selects between the two available sleep modes. When SM is cleared (zero), Idle Mode is selected as Sleep Mode. When SM is set (1), Power Down mode is selected as sleep mode. The AT43USB353M does not support the Idle Mode and SM should always be set to one when entering the Sleep Mode. • Bit 3, 2 – ISC11, ISC10: Interrupt Sense Control 1 Bit 1 and Bit 0 The External Interrupt 1 is activated by the external pin INT1 if the SREG I-flag and the corre- sponding interrupt mask in the GIMSK is set. The level and edges on the external INT1 pin that activate the interrupt are defined in Table 10. • Bit 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 bit 1 and bit 0 The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the corre- sponding interrupt mask in the GIMSK is set. The level and edges on the external INT0 pin that activate the interrupt are defined in Table 10. Bit 7 6 5 4 3 2 1 0 $35 ($55) – – SE SM ISC11 ISC10 ISC01 ISC00 MCUCR Read/Write R R R/W R/W R/W R/W R/W R/W Initial Value 0 0 0 0 0 0 0 0 Table 9. INT1 Sense Control ISC11 ISC10 Description 0 0 The low level of INT1 generates an interrupt request. 01 Reserved. 1 0 The falling edge of INT1 generates an interrupt request. 1 1 The rising edge of INT1 generates an interrupt request. Table 10. INT1 Sense Control ISC01 ISC00 Description 0 0 The low level of INT0 generates an interrupt request. 01 Reserved. 1 0 The falling edge of INT0 generates an interrupt request. 1 1 The rising edge of INT0 generates an interrupt request. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |