AT89C5132-ROTUL datasheet(92/181 Pages) ATMEL

92 / 181 page

4173D–USB–02/06

AT89C5132

Figure 16-15. Data Controller Configuration Flows

16.6.3

Data Transmitter

16.6.3.1

Configuration

For transmitting data to the card, user must first configure the data controller in transmission

mode by setting the DATDIR bit in MMCON1 register.

Figure 16-16 summarizes the data stream transmission flows in both polling and interrupt modes

while Figure 16-17 summarizes the data block transmission flows in both polling and interrupt

modes, these flows assume that block length is greater than 16 data.

16.6.3.2

Data Loading

Data is loaded in the FIFO by writing to MMDAT register. Number of data loaded may vary from

1 to 16 Bytes. Then if necessary (more than 16 Bytes to send) user must wait that one FIFO

becomes empty (F1EI or F2EI set) before loading 8 new data.

16.6.3.3

Data Transmission

Transmission is enabled by setting and clearing DATEN bit in MMCON1 register.

Data is transmitted immediately if the response has already been received, or is delayed after

the response reception if its status is correct. In both cases transmission is delayed if a card

sends a busy state on the data line until the end of this busy condition.

According to the MMC specification, the data transfer from the host to the card may not start

sooner than 2 MMC clock periods after the card response was received (formally N

WR parame-

ter). To address all card types, this delay can be programmed using DATD1:0 Bits in MMCON2

when DATD2:0 Bits are set, by step of 2 MMC clock periods.

16.6.3.4

End of Transmission

The end of data frame (block or stream) transmission is signalled by the EOFI flag in MMINT

page 96.

In data stream mode, EOFI flag is set, after reception of the End bit. This assumes user has pre-

viously sent the STOP command to the card, which is the only way to stop stream transfer.

In data block mode, EOFI flag is set, after reception of the CRC status token (see Figure 16-4).

Two other flags in MMSTA register: DATFS and CRC16S report a status on the frame sent.

DATFS indicates if the CRC status token format is correct or not, and CRC16S indicates if the

card has found the CRC16 of the block correct or not.

Data Single Block

Configuration

Data Stream

Configuration

Configure Format

DFMT = 0

Data Multi-block

Configuration

Configure Format

DFMT = 1

MBLOCK = 1

BLEN3:0 = XXXXb

Configure Format

DFMT = 1

MBLOCK = 0

BLEN3:0 = XXXXb

AT89C5132-ROTUL 데이터시트(PDF) 92 Page - ATMEL Corporation

AT89C5132-ROTUL 데이터시트(HTML) 92 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL