P82C150AHT datasheet(18/36 Pages) PHILIPS

18 / 36 page

1996 Jun 19

Philips Semiconductors

Preliminary speciﬁcation

CAN Serial Linked I/O device (SLIO) with

digital and analog port functions

P82C150

7.3.5

BIT TIMING

The Nominal Bit Time of the P82C150 is subdivided into 10

Time Quanta. The Synchronization Time Segment

(SYNC_SEG) and the Propagation Time Segment

(PROP_SEG) are each one Time Quantum long. The

Phase Buffer Segment 1 (PHASE_SEG1) and the Phase

Buffer Segment 2 (PHASE_SEG2) are each four Time

Quanta long. The Resynchronization Jump Width (SJW) is

four Time Quanta long.

The sample point is located at the end of the Phase Buffer

Segment 1. The Nominal Bit Time is internally adjusted to

that bit timing which is provided by the crystal driven host

(calibration message).

The usable bus length at a given bit rate is reduced in

comparison to other CAN controllers with programmable

bit timing because the Propagation Time Segment is fixed

to 1

⁄10 length of the Nominal Bit Time. The bit segmentation

of the crystal driven host should be programmed like the

fixed bit segmentation of the P82C150, e.g. one bit time

segment is 1

⁄10 length of the Nominal Bit Time (refer also

to Table 15 for bit time programming).

Table 11 Bit time subdivision

1 BIT TIME

BT1

BT2

BT3

BT4

BT5

BT6

BT7

BT8

BT9

BT10

SYNC_SEG PROP_SEG

PHASE_SEG1

PHASE_SEG2

7.3.6

CAN-BUS TRANSCEIVER

The transceiver of the P82C150 consists of the

configurable input comparator and of complementary

open-drain driver outputs. The reference voltage REF is

an additional output.

7.3.6.1

CAN-bus input comparator (RX0, RX1)

The input comparator monitors the transient voltage on

RX1 and RX0.

The result of the input comparator is logic 1 if the voltage

levels of the CAN-bus lines are regarded as recessive, and

logic 0 if they are regarded as dominant.

The recessive state and the dominant state are not

equivalent and may not be mixed-up.

The input comparator is configurable depending on the

four CAN-bus modes (see Table 10), supporting

battery-powered applications (Sleep Mode) and tolerance

against bus wiring failures.

7.3.6.2

CAN-bus output drivers (TX0, TX1)

The output driver function is shown in Table 12. The output

driver TX1 is disabled in bus mode 2 to tolerate a

short-circuit between the CAN-bus lines in a two-wire

differential CAN physical layer.

Table 12 CAN-bus driver output function

CAN OUTPUT

RECESSIVE

DOMINANT

RESET STATE, BUS-OFF AND

SLEEP MODE (MODE 3)

MODES 0 AND 1

MODE 2

TX0

ﬂoating

LOW

ﬂoating

TX1

ﬂoating

HIGH

ﬂoating

P82C150AHT 데이터시트(PDF) 18 Page - NXP Semiconductors

P82C150AHT 데이터시트(HTML) 18 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

데이터시트 다운로드

링크 URL