| 전자부품 데이터시트 검색엔진 |
|
PCD5003 데이터시트(PDF) 24 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCD5003 데이터시트(HTML) 24 Page - NXP Semiconductors |
|
24 / 44 page ![]() 1997 Jun 24 24 Philips Semiconductors Product specification Advanced POCSAG Paging Decoder PCD5003 7.48 EEPROM access limitations Since the EEPROM address pointer is used during data decoding, the EEPROM may not be accessed while the receiver is active (RXE = 1). It is advised to switch to OFF state before accessing the EEPROM. The EEPROM cannot be written unless the EEPROM programming enable bit (bit D1) in the control register is set. For writing a minimum supply voltage VPG is required (2.0 V typ.). The supply current needed during writing (IPG) will be ≈500 µA. Any modified SPF settings (bytes 0 to 3) only take effect after a decoder reset. Modified identifiers are active immediately. 7.49 EEPROM read operation EEPROM read operations must start at a valid address in the non-contiguous memory map. Single-byte or block reads are permitted. 7.50 EEPROM write operation EEPROM write operations must always take place in blocks of 6 bytes, starting at the beginning of a row. Programming a single byte will reset the other bytes in the same row. Modifying a single byte in a row requires re-writing the unchanged bytes with their old contents. After writing each block a pause of maximum 7.5 ms is required to complete the programming operation internally. During this time the external microcontroller may generate an I2C-bus stop condition. If another I2C-bus transfer is started the decoder will pull SCL LOW during this pause. After writing the EEPROM programming enable bit (D1) in the control register must be reset. 7.51 Invalid write address When an invalid write address is used, the column counter bits (D2 to D0) are forced to zero before being loaded into the address pointer. The row counter bits are used normally. 7.52 Incomplete programming sequence A programming sequence may be aborted by an I2C-bus stop condition. Next, the EEPROM programming enable bit (D1) in the control register must be reset. Any bytes received of the last 6-byte block will be ignored and the contents of this (incomplete) EEPROM block will remain unchanged. 7.53 Unused EEPROM locations A total of 20 EEPROM bytes is available for general purpose storage (see Table 19). Fig.10 EEPROM organization and access. handbook, full pagewidth COLUMN ROW 0 1 2 3 4 5 6 7 0 D7 D0 D7 D0 ADDRESS POINTER ROW COLUMN I/O REGISTER 01 0 1 0 0 SPF bits Synthesizer data Identifiers unused bytes 1 I D MLC254 12 3 4 5 2 I D 3 I D 4 I D 5 I D 6 I D |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |