| 전자부품 데이터시트 검색엔진 |
|
56F8322 데이터시트(PDF) 86 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
56F8322 데이터시트(HTML) 86 Page - Freescale Semiconductor, Inc |
|
86 / 136 page ![]() 56F8322 Techncial Data, Rev. 16 86 Freescale Semiconductor Preliminary 6.5.6.3 IRQ—Bit 10 This bit controls the pull-up resistors on the IRQA pin. 6.5.6.4 Reserved—Bits 9–4 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 6.5.6.5 JTAG—Bit 3 This bit controls the pull-up resistors on the TRST (This pin is always tied inactive on the 56F8322), TMS and TDI pins. 6.5.6.6 Reserved—Bits 2–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 6.5.7 CLKO Select Register (SIM_CLKOSR) The CLKO select register can be used to multiplex out any one of the clocks generated inside the clock generation and SIM modules. The default value is SYS_CLK. All other clocks primarily muxed out are for test purposes only, and are subject to significant unspecified latencies at high frequencies. The upper four bits of the GPIOB register can function as GPIO, Quad Decoder #0 signals, or as additional clock output signals. GPIO has priority and is enabled/disabled via the GPIOB_PER. If GPIOB[7:4] are programmed to operate as peripheral outputs, then the choice between Quad Decoder #0 and additional clock outputs is made here in the CLKOSR. The default state is for the peripheral function of GPIOB[7:4] to be programmed as Quad Decoder #0. This can be changed by altering PHASE0 through INDEX as shown in Figure 6-9. The CLKOUT pin is not bonded out in this device. Instead, it is offered only as a pad for die-level testing. Figure 6-9 CLKO Select Register (SIM_CLKOSR) 6.5.7.1 Reserved—Bits 15–10 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 6.5.7.2 PHASEA0 (PHSA)—Bit 9 • 0 = Peripheral output function of GPIOB[7] is defined to be PHASEA0 • 1 = Peripheral output function of GPI B[7] is defined to be the oscillator clock (MSTR_OSC, see Figure 3-4) 6.5.7.3 PHASEB0 (PHSB)—Bit 8 • 0 = Peripheral output function of GPIOB[6] is defined to be PHASEB0 • 1 = Peripheral output function of GPIOB[6] is defined to be SYS_CLK2 Base + $A 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read 0 0 0 0 0 0 PHSA PHSB INDEX HOME CLK DIS CLKOSEL Write RESET 0 0 000 0 0 0 0 0 1 0 0 0 0 0 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |