| 전자부품 데이터시트 검색엔진 |
|
M68HC05 데이터시트(PDF) 75 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
M68HC05 데이터시트(HTML) 75 Page - Freescale Semiconductor, Inc |
|
75 / 118 page ![]() SPI Registers MC68HC05C9A Advance Information Data Sheet, Rev. 4.1 Freescale Semiconductor 75 SPIE — Serial Peripheral Interrupt Enable Bit This read/write bit enables SPI interrupts. Reset clears the SPIE bit. 1 = SPI interrupts enabled 0 = SPI interrupts disabled SPE — Serial Peripheral System Enable Bit This read/write bit enables the SPI. Reset clears the SPE bit. 1 = SPI system enabled 0 = SPI system disabled DWOM — Port D Wire-OR Mode Option Bit This read/write bit disables the high side driver transistors on port D outputs so that port D outputs become open-drain drivers. DWOM affects all seven port D pins together. This option is only available when configured as a C9A. 1 = Port D outputs act as open-drain outputs. 0 = Port D outputs are normal CMOS outputs. MSTR — Master Mode Select Bit This read/write bit selects master mode operation or slave mode operation. Reset clears the MSTR bit. 1 = Master mode 0 = Slave mode CPOL — Clock Polarity Bit When the clock polarity bit is cleared and data is not being transferred, a steady state low value is produced at the SCK pin of the master device. Conversely, if this bit is set, the SCK pin will idle high. This bit is also used in conjunction with the clock phase control bit to produce the desired clock-data relationship between master and slave. See Figure 10-1. CPHA — Clock Phase Bit The clock phase bit, in conjunction with the CPOL bit, controls the clock-data relationship between master and slave. The CPOL bit can be thought of as simply inserting an inverter in series with the SCK line. The CPHA bit selects one of two fundamentally different clocking protocols. When CPHA = 0, the shift clock is the OR of SCK with SS. As soon as SS goes low, the transaction begins and the first edge on SCK invokes the first data sample. When CPHA=1, the SS pin may be thought of as a simple output enable control. See Figure 10-1. SPR1 and SPR0 — SPI Clock Rate Selects These read/write bits select one of four master mode serial clock rates, as shown in Table 10-1. They have no effect in the slave mode. $000A Bit 7 654321 Bit 0 Read: SPIE SPE DWOM (C9A) MSTR CPOL CPHA SPR1 SPR0 Write: Reset: 000001 U U U = Undetermined Figure 10-4. SPI Control Register (SPCR) |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |