| 전자부품 데이터시트 검색엔진 |
|
CDCE949 데이터시트(PDF) 10 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
CDCE949 데이터시트(HTML) 10 Page - Texas Instruments |
|
10 / 31 page ![]() DEFAULT DEVICE SETTING EEPROM Xin Xout V DD GND V DDOUT X-tal Y2=27MHz Y1=27MHz Y3=27MHz LV CMOS Pdiv1=1 Y4=27MHz Y5=27MHz Y6=27MHz Y7=27MHz Y8=27MHz Y9=27MHz LV CMOS Pdiv9=1 Pdiv8=1 LV CMOS LV CMOS Pdiv7=1 Pdiv6=1 LV CMOS LV CMOS Pdiv5=1 Pdiv4=1 LV CMOS LV CMOS Pdiv3=1 Pdiv2=1 LV CMOS Programming and SDA/SCL Register InputClock PLL Bypass PLL 1 powerdown PLL Bypass PLL 2 powerdown PLL Bypass PLL 3 powerdown PLL Bypass PLL 4 powerdown S0 SDA SCL 27MHz Crystal ProgrammingBus “1” =outputsenabled “0” =outputs3-State CDCE949 CDCEL949 SCAS844 – JUNE 2007 Table 3. Y1 Setting(1) Y1 SELECTION Y1 FUNCTION 0 State 0 1 State 1 (1) State0 and State1 are user-definable in Generic Configuration Register and can be power down, 3-state, low or active. The S1/SDA and S2/SCL pins of the CDCE949/CDCEL949 are dual-function pins. In the default configuration they are defined as SDA/SCL for the serial interface. They can be programmed as control pins (S1/S2) by setting the appropriate bits in the EEPROM. Note that changes to the Control register (Bit [6] of Byte 02) have no effect until they are written into the EEPROM. Once they are set as control pins, the serial programming interface is no longer available. However, if VDDOUT is forced to GND, the two control-pins, S1 and S2, temporarily act as serial programming pins (SDA/SCL). S0 is not a multi-use pin, it is a control pin only. The internal EEPROM of CDCE949/CDCEL949 is preconfigured as shown in Figure 6. (The input frequency is passed through to the output as a default.) This allows the device to operate in default mode without the extra production step of programming it. The default setting appears after power is supplied or after a power-down/up sequence until it is reprogrammed by the user to a different application configuration. A new register setting is programmed via the serial SDA/SCL Interface. Figure 6. Default Configuration A different default setting can be programmed upon customer request. Contact Texas Instruments sales or marketing representative for more information. Table 4 shows the default setting for the Control Terminal Register (external control pins). In normal operation, all 8 register settings are available, but in the default configuration only the first two settings (0 and 1) can be selected with S0, as S1 and S2 are configured as programming pins in default mode. 10 Submit Documentation Feedback |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |