 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
PIC18F44J10-E/ML 데이터시트(PDF) 209 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F44J10-E/ML 데이터시트(HTML) 209 Page - Microchip Technology |
|
|
209 / 358 page  © 2007 Microchip Technology Inc. Preliminary DS39682C-page 207 PIC18F45J10 FAMILY 16.4.2 EUSART SYNCHRONOUS SLAVE RECEPTION The operation of the Synchronous Master and Slave modes is identical, except in the case of Sleep, or any Idle mode and bit SREN, which is a “don’t care” in Slave mode. If receive is enabled by setting the CREN bit prior to entering Sleep or any Idle mode, then a word may be received while in this low-power mode. Once the word is received, the RSR register will transfer the data to the RCREG register; if the RCIE enable bit is set, the inter- rupt generated will wake the chip from the low-power mode. If the global interrupt is enabled, the program will branch to the interrupt vector. To set up a Synchronous Slave Reception: 1. Enable the synchronous master serial port by setting bits SYNC and SPEN and clearing bit CSRC. 2. If interrupts are desired, set enable bit RCIE. 3. If 9-bit reception is desired, set bit RX9. 4. To enable reception, set enable bit CREN. 5. Flag bit, RCIF, will be set when reception is complete. An interrupt will be generated if enable bit, RCIE, was set. 6. Read the RCSTA register to get the 9th bit (if enabled) and determine if any error occurred during reception. 7. Read the 8-bit received data by reading the RCREG register. 8. If any error occurred, clear the error by clearing bit CREN. 9. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. TABLE 16-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 43 PIR1 PSPIF(1) ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF TMR1IF 45 PIE1 PSPIE(1) ADIE RCIE TXIE SSP1IE CCP1IE TMR2IE TMR1IE 45 IPR1 PSPIP(1) ADIP RCIP TXIP SSP1IP CCP1IP TMR2IP TMR1IP 45 RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 45 RCREG EUSART Receive Register 45 TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 45 BAUDCON ABDOVF RCIDL —SCKP BRG16 — WUE ABDEN 45 SPBRGH EUSART Baud Rate Generator Register High Byte 45 SPBRG EUSART Baud Rate Generator Register Low Byte 45 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception. Note 1: These bits are not implemented on 28-pin devices and should be read as ‘0’. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
