PIC18F4685-ISLASHSP datasheet(44/484 Pages) MICROCHIP

44 / 484 page

PIC18F2682/2685/4682/4685

DS39761B-page 42

Preliminary

RCON: RESET CONTROL REGISTER

R/W-0

R/W-1(1)

U-0

R/W-1

R-1

R/W-0(2)

R/W-0

IPEN

SBOREN

—RI

POR

BOR

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 7

IPEN: Interrupt Priority Enable bit

= Enable priority levels on interrupts

= Disable priority levels on interrupts (PIC16CXXX Compatibility mode)

bit 6

SBOREN: BOR Software Enable bit(1)

If BOREN1:BOREN0 = 01:

= BOR is enabled

= BOR is disabled

If BOREN1:BOREN0 = 00, 10 or 11:

Bit is disabled and read as ‘0’.

bit 5

Unimplemented: Read as ‘0’

bit 4

RI: RESET Instruction Flag bit

= The RESET instruction was not executed (set by firmware only)

= The RESET instruction was executed causing a device Reset (must be set in software after a

Brown-out Reset occurs)

bit 3

TO: Watchdog Time-out Flag bit

= Set by power-up, CLRWDT instruction or SLEEP instruction

= A WDT time-out occurred

bit 2

PD: Power-Down Detection Flag bit

= Set by power-up or by the CLRWDT instruction

= Set by execution of the SLEEP instruction

bit 1

POR: Power-on Reset Status bit

= A Power-on Reset has not occurred (set by firmware only)

= A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)

bit 0

BOR: Brown-out Reset Status bit

= A Brown-out Reset has not occurred (set by firmware only)

= A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)

Note 1:

If SBOREN is enabled, its Reset state is ‘1’; otherwise, it is ‘0’.

The actual Reset value of POR is determined by the type of device Reset. See the notes following this

Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent

Power-on Resets may be detected.

2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to

‘1’ by software immediately after a Power-on Reset).

PIC18F4685-I/SP 데이터시트(PDF) 44 Page - Microchip Technology

PIC18F4685-I/SP 데이터시트(HTML) 44 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL