PIC18F4685-ISLASHSP datasheet(192/484 Pages) MICROCHIP

192 / 484 page

PIC18F2682/2685/4682/4685

DS39761B-page 190

Preliminary

17.3.2

OPERATION

When initializing the SPI, several options need to be

specified. This is done by programming the appropriate

control bits (SSPCON1<5:0> and SSPSTAT<7:6>).

These control bits allow the following to be specified:

• Master mode (SCK is the clock output)

• Slave mode (SCK is the clock input)

• Clock Polarity (Idle state of SCK)

• Data Input Sample Phase (middle or end of data

output time)

• Clock Edge (output data on rising/falling edge of

SCK)

• Clock Rate (Master mode only)

• Slave Select mode (Slave mode only)

The MSSP module consists of a transmit/receive shift

SSPSR shifts the data in and out of the device, MSb

first. The SSPBUF holds the data that was written to the

SSPSR until the received data is ready. Once the 8 bits

of data have been received, that byte is moved to the

SSPBUF register. Then, the Buffer Full detect bit, BF

(SSPSTAT<0>) and the interrupt flag bit, SSPIF, are

set. This double-buffering of the received data

(SSPBUF) allows the next byte to start reception before

reading the data that was just received. Any write to the

SSPBUF register during transmission/reception of data

will be ignored and the write collision detect bit, WCOL

(SSPCON1<7>), will be set. User software must clear

the WCOL bit so that it can be determined if the follow-

ing write(s) to the SSPBUF register completed

successfully.

When the application software is expecting to receive

valid data, the SSPBUF should be read before the next

byte of data to transfer is written to the SSPBUF. The

Buffer Full bit, BF (SSPSTAT<0>), indicates when

SSPBUF has been loaded with the received data

(transmission is complete). When the SSPBUF is read,

the BF bit is cleared. This data may be irrelevant if the

SPI is only a transmitter. Generally, the MSSP interrupt

is used to determine when the transmission/reception

has completed. The SSPBUF must be read and/or

written. If the interrupt method is not going to be used,

then software polling can be done to ensure that a write

collision does not occur. Example 17-1 shows the

loading of the SSPBUF (SSPSR) for data transmission.

The SSPSR is not directly readable or writable and can

only be accessed by addressing the SSPBUF register.

Additionally, the MSSP Status register (SSPSTAT)

indicates the various status conditions.

EXAMPLE 17-1:

LOADING THE SSPBUF (SSPSR) REGISTER

LOOP

BTFSS

SSPSTAT, BF

;Has data been received (transmit complete)?

BRA

LOOP

;No

MOVF

SSPBUF, W

;WREG reg = contents of SSPBUF

MOVWF

RXDATA

;Save in user RAM, if data is meaningful

MOVF

TXDATA, W

;W reg = contents of TXDATA

MOVWF

SSPBUF

;New data to xmit

PIC18F4685-I/SP 데이터시트(PDF) 192 Page - Microchip Technology

PIC18F4685-I/SP 데이터시트(HTML) 192 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL