TMP88CS43FG datasheet(82/218 Pages) TOSHIBA

82 / 218 page

Page 72

8. 16-Bit TimerCounter 1 (TC1)

8.3 Function

TMP88CS43FG

8.3.2 External Trigger Timer Mode

In the external trigger timer mode, the up-counter starts counting by the input pulse triggering of the TC1

pin, and counts up at the edge of the internal clock. For the trigger edge used to start counting, either the rising

or falling edge is defined in TC1CR<TC1S>.

• When TC1CR<METT1> is set to “1” (trigger start and stop)

When a match between the up-counter and the TC1DRA value is detected after the timer starts, the

up-counter is cleared and halted and an INTTC1 interrupt request is generated.

If the edge opposite to trigger edge is detected before detecting a match between the up-counter

and the TC1DRA, the up-counter is cleared and halted without generating an interrupt request.

Therefore, this mode can be used to detect exceeding the specified pulse by interrupt.

After being halted, the up-counter restarts counting when the trigger edge is detected.

• When TC1CR<METT1> is set to “0” (trigger start)

When a match between the up-counter and the TC1DRA value is detected after the timer starts, the

up-counter is cleared and halted and an INTTC1 interrupt request is generated.

The edge opposite to the trigger edge has no effect in count up. The trigger edge for the next count-

ing is ignored if detecting it before detecting a match between the up-counter and the TC1DRA.

Since the TC1 pin input has the noise rejection, pulses of 4/fc [s] or less are rejected as noise. A pulse width

of 12/fc [s] or more is required to ensure edge detection.

Example 1 :Generating an interrupt 1 ms after the rising edge of the input pulse to the TC1 pin

(fc =20 MHz, CGCR<DV1CK> = “1”)

LDW

(TC1DRA), 007DH

; 1ms

÷ 27/fc = 7DH

; IMF

= “0”

SET

(EIRD). 2

; Enables INTTC1 interrupt

; IMF

= “1”

(TC1CR), 00001000B

; Selects the source clock and mode

(TC1CR), 00111000B

; Starts TC1 external trigger, METT1

= 0

Example 2 :Generating an interrupt when the low-level pulse with 4 ms or more width is input to the TC1 pin

(fc =20 MHz, CGCR<DV1CK> = “1”)

LDW

(TC1DRA), 0138H

; 4 ms

÷ 28/fc = 0138H

; IMF

= “0”

SET

(EIRD). 2

; Enables INTTC1 interrupt

; IMF

= “1”

(TC1CR), 00000100B

; Selects the source clock and mode

(TC1CR), 01110100B

; Starts TC1 external trigger, METT1

= 0

TMP88CS43FG 데이터시트(PDF) 82 Page - Toshiba Semiconductor

TMP88CS43FG 데이터시트(HTML) 82 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL