| 전자부품 데이터시트 검색엔진 |
|
DM300019 데이터시트(PDF) 34 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
DM300019 데이터시트(HTML) 34 Page - Microchip Technology |
|
34 / 50 page ![]() dsPICDEM™ 80-Pin Starter Development Board User’s Guide DS51584B-page 30 © 2006 Microchip Technology Inc. 3.5 BOARD SELF-TEST The board self-test is provided for completeness only. Users do not need to run this test. 1. Power the board using a 9V DC supply and the barrel power connector. The LED marked D1 turns ON. If D1 does not light: - the LED is dead, or - the regulator is dead, or - the DC supply is not connected to the AC wall plug 2. Using a DMM set for DCV, check that 3.3V or 5.0V is available at location marked VDD and GND on the 80-pin header. 3. Connect a shorting plug on the RS-232 connector J1. This shorting plug should have pins 2 and 3 connected to one another. 4. Short pins 2 and 3 on line connector J9 using a 0.1 ″ jumper. 5. Make sure J4 has a 0.1 ″ jumper on it. 6. To enter the Self-Test mode, hold down S1, press and release MCLR, then release S1. The following four tests should run: Test Description UART Test This automatic test transmits 5 characters and receives them through the serial port. During the test, LED RD4 blinks at a very fast rate (8 blinks/sec). However, this test completes so quickly that, in most instances, no noticeable blink of RD4 will occur. Keypad Test During this test, LED RD5 blinks very fast. You must respond by pressing S1 and S2. When you press S1, RD4 lights. When you press S2, RD7 lights. If both key presses are acknowledged by the dsPIC® DSC, then the test passed. If you get no response or an incorrect response within 4 seconds, then the test is considered failed. In either case the test automatically proceeds to the Potentiometer test. Potentiometer Test During this test, LED RD6 blinks rapidly. You must first respond by turn- ing Potentiometer R13 fully clockwise (RD4 will light) and then fully coun- terclockwise (RD7 will light). Then you must move the potentiometer wiper to a center position causing RD5 to light up. When this happens, the test is complete. This test must be completed in 8 seconds or else the test is considered failed. Tone Test This procedure automatically tests the digital potentiometer and analog operational amplifier. A sine wave, generated using the digital potentiom- eter, is sent through the Op Amp circuit to the ADC of the dsPIC DSC device. The sine wave is analyzed to determine if a smooth sine wave has been generated. If all works well, the test passes. If there is a fault in the op amp or digital potentiometer, then this test fails. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |