| 전자부품 데이터시트 검색엔진 |
|
INA209 데이터시트(PDF) 14 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
INA209 데이터시트(HTML) 14 Page - Texas Instruments |
|
14 / 50 page ![]() The PV pin allows for a 0V output that indicates a power-invalid condition. An output equal to the pull-up supply voltage connected to the VPU pin indicates a power-valid condition, as shown in Figure 7-2. Dividing down the high power-valid pull-up voltage by adding a resistor to ground at the PV output is also possible, thus allowing this function to interface with lower-voltage circuitry, if needed. Power-Valid Detection INA3221 VS PV VPU RPU RPU_ext RDIV (1) A. RDIV can be used to level-shift the PV output high. Figure 7-2. Power-Valid Output Structure 7.3.2.4 Timing-Control Alert The INA3221 timing-control alert function helps verify proper power-supply sequencing. At power-up, the default INA3221 setting is continuous shunt- and bus-voltage conversion mode, and the INA3221 internally begins comparing the channel-1 bus voltage to determine when a 1.2V level is reached. This comparison is made each time the sequence returns to the channel-1 bus-voltage measurement. When a 1.2V level is detected on the channel-1 bus-voltage measurement, the INA3221 begins checking for a 1.2V level present on the channel-2 bus-voltage measurement. After a 1.2V level is detected on channel 1, if the INA3221 does not detect a 1.2V value or greater on the bus voltage measurement following four complete cycles of all three channels, the timing control (TC) alert pin pulls low to indicate that the INA3221 has not detected a valid power rail on channel 2. As shown in Figure 7-3, this sequence allows for approximately 28.6ms from the time 1.2V is detected on channel 1 for a valid voltage to be detected on channel 2. Figure 7-4 illustrates the state diagram for the TC alert pin. S Ch 1 S Ch 2 S Ch 3 S Ch 1 S Ch 2 S Ch 3 S Ch 1 S Ch 2 S Ch 3 S Ch 1 S Ch 2 S Ch 3 S Ch 1 S Ch 2 S Ch 3 Signal Channel 1.2V Detected on Channel-1 Bus-Voltage Measurement Measure For 1.2V on Channel-2 Bus Voltage 2.2ms 28.6ms B B B B B B B B B B B B B B B NOTE: The signal refers to the corresponding shunt (S) and bus (B) voltage measurement for each channel. Figure 7-3. Timing Control Timing Diagram 1.2V Detected on Channel-1 Bus-Voltage Measurement Measure for 1.2V on Channel-2 Bus Voltage 1.2V on Channel 2 Detected 1.2V on Channel 2 Not Detected Timing Control Output High Low 28.6ms Figure 7-4. Timing Control State Diagram INA3221 SBOS576C – MAY 2012 – REVISED SEPTEMBER 2025 www.ti.com 14 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated Product Folder Links: INA3221 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |