ANT-2.4-CW-RCL-RPS datasheet(63/73 Pages) MICROCHIP

63 / 73 page

WINCS02IC and WINCS02 Family

Appendix A: Regulatory Approval

Data Sheet

DS70005577B - 63

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•

Consult the dealer or an experienced radio/TV technician for help

Additional information on labeling and user information requirements for Part 15 devices can be

found in KDB Publication 784748, which is available at the FCC Office of Engineering and Technology

(OET) Laboratory Division Knowledge Database (KDB) apps.fcc.gov/oetcf/kdb/index.cfm.

5.1.2

RF Exposure

All transmitters regulated by FCC must comply with RF exposure requirements. KDB 447498 General

RF Exposure Guidance provides guidance in determining whether proposed or existing transmitting

facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF)

fields adopted by the Federal Communications Commission (FCC).

From the FCC Grant: Output power listed is conducted. This grant is valid only when the module is

sold to OEM integrators and must be installed by the OEM or OEM integrators. This transmitter is

restricted for use with the specific antenna(s) tested in this application for Certification and must

not be co-located or operating in conjunction with any other antenna or transmitters within a host

device, except in accordance with FCC multi-transmitter product procedures.

WINCS02PC/WINCS02PE/WINCS02UC/WINCS02UE: These modules are approved for installation into

mobile or/and portable host platforms.

5.1.3

Approved Antenna Types

To maintain modular approval in the United States, only the tested antenna types are used. It is

permissible to use different antenna, provided the same antenna type, antenna gain (equal to or

less than), with similar in-band and out-of band characteristics (refer to specification sheet for cutoff

frequencies).

For the WINCS02PC/PE, the approval is received using the integral PCB antenna.

For the WINCS02UC/UE, approved antennas are listed in the WINCS02 Module Approved External

Antenna.

5.1.4

Helpful Web Sites

• Federal Communications Commission (FCC): www.fcc.gov.

• FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB)

apps.fcc.gov/oetcf/kdb/index.cfm.

5.2

Canada

The WINCS02PC/WINCS02PE/WINCS02UC/WINCS02UE Modules have been certified for use in

Canada under Innovation, Science and Economic Development Canada (ISED, formerly Industry

Canada) Radio Standards Procedure (RSP) RSP-100, Radio Standards Specification (RSS) RSS-Gen and

RSS-247. Modular approval permits the installation of a module in a host device without the need to

recertify the device.

ANT-2.4-CW-RCL-RPS 데이터시트(PDF) 63 Page - Microchip Technology

ANT-2.4-CW-RCL-RPS 데이터시트(HTML) 63 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

데이터시트 다운로드

링크 URL