AS3701 datasheet(49/110 Pages) AMSOSRAM

49 / 110 page

Page 48

ams Datasheet

Document Feedback

[v1-11] 2016-Dec-14

AS3701 − Detailed Description – System Functions

Interrupt Output

GPIOx pin logic state is derived from the interrupt signal XIRQ.

Whenever an interrupt is present the GPIOx pin will be pulled

high.

The gpioX_mode [GPIOxcontrol] should be set to output.

The gpioX_iosf [GPIOxcontrol] should be set to Interrupt output.

For GPIO1 and GPIO2, the Interrupt output signal can be

visualized via the Current sinks. In this case the gpioX_mode

[GPIOxcontrol] should be set to CURRx.

VSUP_low Output

GPIOx pin will go high, if VSUP falls below ResVoltFall and

SupResEn [Battery_voltage_monitor] = 0.

The gpioX_mode [GPIOxcontrol] should be set to output.

The gpioX_iosf [GPIOxcontrol] should be set to VSUP_low output.

For GPIO1 and GPIO2, the VSUP_low output signal can be

visualized via the Current sinks. In this case the gpioX_mode

[GPIOxcontrol] should be set to CURRx.

PWRGOOD Output

This signal will go high at the end of the start-up sequence. This

can be used as a second reset signal to the processor to e.g.

start oscillators.

The gpioX_mode [GPIOxcontrol] should be set to output.

The gpioX_iosf [GPIOxcontrol] should be set to Pwr_good output.

For GPIO1 and GPIO2, the Pwr_good output signal can be

visualized via the Current sinks. In this case the gpioX_mode

[GPIOxcontrol] should be set to CURRx.

Charger Active Output

When selected, the GPIOx will go high if the charger is active.

The gpioX_mode [GPIOxcontrol] should be set to output.

The gpioX_iosf [GPIOxcontrol] should be set to Charger active

output.

For GPIO1 and GPIO2, the Charger active output signal can be

visualized via the Current sinks. In this case the gpioX_mode

[GPIOxcontrol] should be set to CURRx.

EOC Output

When selected, the GPIOx will go high if the charger has reached

the EOC state.

The gpioX_mode [GPIOxcontrol] should be set to output.

The gpioX_iosf [GPIOxcontrol] should be set to EOC output.

For GPIO1 and GPIO2, the EOC output signal can be visualized

via the Current sinks. In this case the gpioX_mode [GPIOxcontrol]

should be set to CURRx.

AS3701 데이터시트(PDF) 49 Page - ams-OSRAM AG

AS3701 데이터시트(HTML) 49 Page - ams-OSRAM AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL