STPCCLIENT datasheet(26/48 Pages) STMICROELECTRONICS

26 / 48 page

UPDATE HISTORY FOR PIN DESCRIPTION CHAPTER

26/48

Issue 1.7 - February 8, 2000

The following changes have been made to the Pin Description Chapter from Revision 1.0 to Release 1.2.

Section

Change

Text

2.1.

Replaced

“internal” With “assimilated “

2.2.1.

Replaced

“The DRAM controller to execute the host transactions is also driven by this

clock”

With

“This clock drives the DRAM controller to execute the host transactions”

2.2.1.

Replaced

“AD[31:0]

PCI Address/Data. This is the 32-bit multiplexed address and data

bus of the PCI. This bus is driven by the master during the address phase and

data phase of write transactions. It is driven by the target during data phase of

read transactions.”

With

“AD[31:0]

PCI Address/Data. This is the 32-bit PCI multiplexed address and

data bus. This bus is driven by the master during the address phase and data

phase of write transactions. It is driven by the target during data phase of read

transactions.”

2.2.6.

Replaced

“IDE devices are connected to SA[19:8] directly and ISA bus is connected to

these pins through two LS245 transceivers. The OE of the transceivers are

connected to ISAOE# and the DIR is connected to MASTER#. The A bus sig-

nals of the transceivers are connected to CPC and IDE DD bus and the B bus

signals are connected to ISA SA bus.”

With

“IDE devices are connected to SA[19:8] directly and the ISA bus is connected

to these pins through two LS245 transceivers. The transceiver OEs are con-

nected to ISAOE# and the DIR is connected to MASTER#. The transceiver bus

signals are connected to the CPC and IDE DD busses and B bus signals are

connected to ISA SA bus.”

2.2.6.

Replaced

“For IDE devices, these signals are used as the DA[2:0] and are connected to

DA[2:0] of IDE devices directly or through a buffer. If the toggling of signals is to

be masked during ISA bus cycles, they can be externally ORed before being

connected to the IDE devices.”

With

“For IDE devices, these signals are used as the DA[2:0] and are connected di-

rectly or through a buffer to DA[2:0] of the IDE devices. If the toggling of signals

are to be masked during ISA bus cycles, they can be externally ORed before

being connected to the IDE devices.”

2.2.8.

Replaced

“IOCS16#

IO Chip Select16. This signal is the decode of the ISA bus SA15-0

address pins of without any qualification of the command signals. The STPC

Client does not drive IOCS16# (similar to PC-AT design). An ISA master ac-

cess to an internal register of the STPC Client is executed as an extended 8-bit

IO cycle.”

With

“IOCS16#

IO Chip Select16. This signal is the decode of SA15-0 address pins

of the ISA address bus without any qualification of the command signals. The

STPC Client does not drive IOCS16# (similar to PC-AT design). An ISA master

access to an internal register of the STPC Client is executed as an extended 8-

bit IO cycle.”

2.2.12.

Added

“They can instead be used for accessing I C devices on board. DDC1 and

DDC0 correspond to SCL and SDA respectively.”

2.2.12.

Replaced

Updated table 3

STPCCLIENT 데이터시트(PDF) 26 Page - STMicroelectronics

STPCCLIENT 데이터시트(HTML) 26 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

데이터시트 다운로드

링크 URL