M32CSLASH86 datasheet(288/505 Pages) RENESAS

288 / 505 page

Page 265

22. Intelligent I/O

)

(

Figures 22.3 to 22.8 show registers associated with the intelligent I/O base timer, the time measurement

function and waveform generating function. (For registers associated with the communication function, see

Figures 22.19 to 22.28.)

Figure 22.3 G1BT Register and G1BCR0 Register

Base Timer Register 1(2)

Symbol

Address

After Reset

G1BT

012116 - 012016

Indeterminate

Function

Setting Range

000016 to FFFF16

b15

When the base timer is counting:

When read, the value of the base timer can be

read.

When write, the counter starts counting from the

value written. When the base timer is reset, the

G1BT register is set to "000016"(1).

When the base timer is reset:

The G1BT register is set to "000016" but value is

indeterminate. No value is written(1).

NOTES:

1. The base timer stops only when the BCK1 and BCK0 bits in the G1BCR0 register are set to "002" (clock

stopped). The base timer counts when the BCK1 and BCK0 bits are set to a value other than "002".

When the BTS bit in the G1BCR1 register is set to "0", the base timer is reset continually, remaining set

to "000016". This, in effect, places the base timer in a "no counting" state. When the BTS bit is set to "1",

this state is cleared and counting starts.

2. The G1BT register reflects the base timer value after one half fBT1 cycle.

Base Timer Control Register 10

Symbol

Address

After Reset

G1BCR0

012216

0016

Bit Name

Function

Bit

Symbol

: Clock stops

: Do not set to this value

: Two-phase pulse signal is applied(1)

: f1

BCK0

BCK1

DIV0

Count Source

Select Bit

DIV1

Count Source

Divide Ratio

Select Bit

DIV2

DIV3

Base Timer

Interrupt Select Bit

0 : Bit 15 overflows

1 : Bit 14 overflows

DIV4

If setting value is n (n = 0 to 31),

count source is divided by 2(n + 1).

No division if n=31.

(n=0) 0 0 0 0 0 : Divide-by-2

(n=1) 0 0 0 0 1 : Divide-by-4

(n=2) 0 0 0 1 0 : Divide-by-6

(n=30) 1 1 1 1 0 : Divide-by-62

(n=31) 1 1 1 1 1 : No division

b6 b5 b4 b3 b2

NOTES:

1. This setting can be used only when the UD1 and UD0 bits in the G1BCR1 register are set to "102"

(two-phase signal processing mode). Do not set the BCK1 and BCK0 bits to "102" when setting the

UD1 and UD0 bits to "002" (counter increment mode) or "012" (Counter increment/decrement mode).

M32C/86 데이터시트(PDF) 288 Page - Renesas Technology Corp

M32C/86 데이터시트(HTML) 288 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL