 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
AT89C5122D-RDRUM 데이터시트(PDF) 93 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
AT89C5122D-RDRUM 데이터시트(HTML) 93 Page - ATMEL Corporation |
|
|
93 / 208 page  93 AT83R5122, AT8xC5122/23 4202F–SCR–07/2008 USB Controller The AT8xC5122D implements a USB device controller supporting Full Speed data transfer. In addition to the default control endpoint 0, it provides 6 other endpoints, which can be configured in Control, Bulk, Interrupt or Isochronous modes: • Endpoint 0: 32-byte FIFO, default control endpoint • Endpoint 1,2,3: 8-byte FIFO • Endpoint 4,5: 64-byte FIFO • Endpoint 6: 2 x 64-byte Ping-pong FIFO This allows the firmware to be developed conforming to most USB device classes, for example: • USB Mass Storage Class Control/Bulk/Interrupt (CBI) Transport, Revision 1.0 - December 14, 1998. • USB Mass Storage Class Bulk-Only Transport, Revision 1.0 - September 31, 1999. • USB Human Interface Device Class, Version 1.1 - April 7, 1999. • USB Device Firmware Upgrade Class, Revision 1.0 - May 13, 1999. USB Mass Storage Classes USB Mass Storage Class CBI Transport Within the CBI framework, the Control endpoint is used to transport command blocks as well as to transport standard USB requests. One Bulk-Out endpoint is used to transport data from the host to the device. One Bulk-In endpoint is used to transport data from the device to the host. And one interrupt endpoint may also be used to signal command completion (protocol 0); it is optional and may not be used (protocol 1). The following configuration adheres to these requirements: • Endpoint 0: 8 bytes, Control In-Out • Endpoint 4: 64 bytes, Bulk-Out • Endpoint 5: 64 bytes, Bulk-In • Endpoint 1: 8 bytes, Interrupt In USB Mass Storage Class Bulk- Only Transport Within the Bulk-Only framework, the Control endpoint is only used to transport class- specific and standard USB requests for device set-up and configuration. One Bulk-Out endpoint is used to transport commands and data from the host to the device. One Bulk- In endpoint is used to transport status and data from the device to the host. No interrupt endpoint is needed. The following configuration adheres to these requirements: • Endpoint 0: 8 bytes, Control In-Out • Endpoint 4: 64 bytes, Bulk-Out • Endpoint 5: 64 bytes, Bulk-In USB Device Firmware Upgrade (DFU) The USB Device Firmware Update (DFU) protocol can be used to upgrade the on-chip program memory of the AT8xC5122D. This allows the implementation of product enhancements and patches to devices that are already in the field. Two different config- urations and description sets are used to support DFU functions. The Run-Time configuration co-exists with the usual functions of the device, which may be USB Mass Storage for the AT8xC5122D. It is used to initiate DFU from the normal operating mode. The DFU configuration is used to perform the firmware update after device re-configura- tion and USB reset. It excludes any other function. Only the default control pipe (endpoint 0) is used to support DFU services in both configurations. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
