| 전자부품 데이터시트 검색엔진 |
|
LPC2158 데이터시트(PDF) 27 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC2158 데이터시트(HTML) 27 Page - NXP Semiconductors |
|
27 / 45 page ![]() LPC2157_2158_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 9 February 2009 27 of 45 NXP Semiconductors LPC2157/2158 Single-chip 16-bit/32-bit microcontrollers The JTAG clock (TCK) must be slower than 1 ⁄ 6 of the CPU clock (CCLK) for the JTAG interface to operate. 6.20.2 RealMonitor RealMonitor is a configurable software module, developed by ARM Inc., which enables real-time debug. It is a lightweight debug monitor that runs in the background while users debug their foreground application. It communicates with the host using the DCC, which is present in the EmbeddedICE logic. The LPC2157/2158 contain a specific configuration of RealMonitor software programmed into the on-chip flash memory. 6.21 LCD driver 6.21.1 General description The LCD segment driver in the LPC2157/2158 can interface to most LCDs using low multiplex rates. It generates the drive signals for static or multiplexed LCDs containing up to four backplanes and up to 32 segments. The LCD controller communicates to a host using the I2C-bus. The I2C-bus clock and data signals for both the microcontroller and the LCD driver are available on the LPC2157/2158 providing system flexibility. Communication overhead to manage the display is minimized by an on-chip display RAM with auto-increment addressing, hardware subaddressing, and display memory switching (static and duplex drive modes). Please refer to PCF8576D data sheet for electrical data. 6.21.2 Functional description The LCD controller is a versatile peripheral device designed to interface microcontrollers to a wide variety of LCDs. It can directly drive any static or multiplexed LCD containing up to four backplanes and up to 32 segments. The display configurations possible with the LCD controller depend on the number of active backplane outputs required. A selection of display configurations is shown in Table 4. All of these configurations can be implemented in a typical system. The microcontroller communicates to the LCD controller using the I2C-bus.The appropriate biasing voltages for the multiplexed LCD waveforms are generated internally. The only other connections required to complete the system are to the power supplies (VDD(LCD), VSS and VLCD) and the LCD panel chosen for the application. 6.21.3 LCD bias voltages LCD biasing voltages are obtained from an internal voltage divider consisting of three series resistors connected between VLCD and VSS. The LCD voltage can be temperature compensated externally via the supply to pin VLCD. A voltage selector drives the multiplexing of the LCD based on programmable configurations. Table 4. Selection of display configurations Number of 7-segments numeric 14-segments alphanumeric Dot matrix Backplanes Segments Digits Indicator symbols Characters Indicator symbols 4 128 16 16 8 16 128 3 9612126 12 96 264 884864 132 442432 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |