ATmega128 datasheet(244/386 Pages) ATMEL

244 / 386 page

244

2467S–AVR–07/09

ATmega128

Note:

1. Can be used for offset calibration.

ADC Control and

Status Register A –

ADCSRA

• Bit 7 – ADEN: ADC Enable

Writing this bit to one enables the ADC. By writing it to zero, the ADC is turned off. Turning the

ADC off while a conversion is in progress, will terminate this conversion.

• Bit 6 – ADSC: ADC Start Conversion

In Single Conversion mode, write this bit to one to start each conversion. In Free Running mode,

write this bit to one to start the first conversion. The first conversion after ADSC has been written

after the ADC has been enabled, or if ADSC is written at the same time as the ADC is enabled,

will take 25 ADC clock cycles instead of the normal 13. This first conversion performs initializa-

tion of the ADC.

ADSC will read as one as long as a conversion is in progress. When the conversion is complete,

it returns to zero. Writing zero to this bit has no effect.

• Bit 5 – ADFR: ADC Free Running Select

When this bit is written to one, the ADC operates in Free Running mode. In this mode, the ADC

samples and updates the data registers continuously. Writing zero to this bit will terminate Free

Running mode.

• Bit 4 – ADIF: ADC Interrupt Flag

This bit is set when an ADC conversion completes and the data registers are updated. The ADC

Conversion Complete Interrupt is executed if the ADIE bit and the I-bit in SREG are set. ADIF is

cleared by hardware when executing the corresponding interrupt handling vector. Alternatively,

ADIF is cleared by writing a logical one to the flag. Beware that if doing a read-modify-write on

ADCSRA, a pending interrupt can be disabled. This also applies if the SBI and CBI instructions

are used.

• Bit 3 – ADIE: ADC Interrupt Enable

When this bit is written to one and the I-bit in SREG is set, the ADC Conversion Complete Inter-

rupt is activated.

• Bits 2:0 – ADPS2:0: ADC Prescaler Select Bits

These bits determine the division factor between the XTAL frequency and the input clock to the

ADC.

11101

ADC5

ADC2

11110

1.23V (VBG)

N/A

11111

0V (GND)

Table 98. Input Channel and Gain Selections (Continued)

MUX4..0

Single Ended

Input

Positive Differential

Input

Negative Differential

Input

Gain

Bit

765

4321

ADEN

ADSC

ADFR

ADIF

ADIE

ADPS2

ADPS1

ADPS0

ADCSRA

Read/Write

R/W

Initial Value

000

0000

ATmega128 데이터시트(PDF) 244 Page - ATMEL Corporation

ATmega128 데이터시트(HTML) 244 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL