ATtiny261-15MZ datasheet(22/227 Pages) ATMEL

22 / 227 page

7753C–AVR–07/09

ATtiny261/ATtiny461/ATtiny861

6.4

I/O Memory

The I/O space definition of the ATtiny261/461/861 is shown in “Register Summary” on page 209.

All ATtiny261/461/861 I/Os and peripherals are placed in the I/O space. All I/O locations may be

accessed by the LD/LDS/LDD and ST/STS/STD instructions, transferring data between the 32

general purpose working registers and the I/O space. I/O Registers within the address range

0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the

value of single bits can be checked by using the SBIS and SBIC instructions. Refer to the

instruction set section for more details. When using the I/O specific commands IN and OUT, the

I/O addresses 0x00 - 0x3F must be used. When addressing I/O Registers as data space using

LD and ST instructions, 0x20 must be added to these addresses.

For compatibility with future devices, reserved bits should be written to zero if accessed.

Reserved I/O memory addresses should never be written.

Some of the Status Flags are cleared by writing a logical one to them. Note that, the CBI and

SBI instructions will only operate on the specified bit, and can therefore be used on registers

containing such Status Flags. The CBI and SBI instructions work with registers 0x00 to 0x1F

only.

The I/O and Peripherals Control Registers are explained in later sections.

6.4.1

General Purpose I/O Registers

The ATtiny261/461/861 contains three General Purpose I/O Registers. These registers can be

used for storing any information, and they are particularly useful for storing global variables and

Status Flags. General Purpose I/O Registers within the address range 0x00 - 0x1F are directly

bit-accessible using the SBI, CBI, SBIS, and SBIC instructions.

6.5

6.5.1

EEARH and EEARL – EEPROM Address Register

• Bit 7:1 – Res6:0: Reserved Bits

These bits are reserved for future use and will always read as 0 in ATtiny261/461/861.

• Bits 8:0 – EEAR8:0: EEPROM Address

The EEPROM Address Registers – EEARH and EEARL – specifies the high EEPROM address

in the 128/256/512 bytes EEPROM space. The EEPROM data bytes are addressed linearly

between 0 and 127/255/511. The initial value of EEAR is undefined. A proper value must be writ-

ten before the EEPROM may be accessed.

Bit

65432

0x1F (0x3F)

-----

EEAR8

EEARH

0x1E (0x3E)

EEAR7

EEAR6

EEAR5

EEAR4

EEAR3

EEAR2

EEAR1

EEAR0

EEARL

Bit

65432

Read/Write

RRR

RRRR

R/W

Read/Write

R/W

Initial Value

00000

Initial Value

XXXX

ATtiny261-15MZ 데이터시트(PDF) 22 Page - ATMEL Corporation

ATtiny261-15MZ 데이터시트(HTML) 22 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL