ATmega325P datasheet(169/364 Pages) ATMEL

169 / 364 page

169

8023F–AVR–07/09

ATmega325P/3250P

Start bit, always low.

(n)

Data bits (0 to 8).

Parity bit. Can be odd or even.

Stop bit, always high.

IDLE

No transfers on the communication line (RxD or TxD). An IDLE line must

high.

The frame format used by the USART is set by the UCSZn2:0, UPMn1:0 and USBSn bits in

UCSRnB and UCSRnC. The Receiver and Transmitter use the same setting. Note that changing

the setting of any of these bits will corrupt all ongoing communication for both the Receiver and

Transmitter.

The USART Character SiZe (UCSZn2:0) bits select the number of data bits in the frame. The

USART Parity mode (UPMn1:0) bits enable and set the type of parity bit. The selection between

one or two stop bits is done by the USART Stop Bit Select (USBSn) bit. The Receiver ignores

the second stop bit. An FEn (Frame Error) will therefore only be detected in the cases where the

first stop bit is zero.

18.4.1

Parity Bit Calculation

The parity bit is calculated by doing an exclusive-or of all the data bits. If odd parity is used, the

result of the exclusive or is inverted. The relation between the parity bit and data bits is as

follows:

even

Parity bit using even parity

Podd

Parity bit using odd parity

Data bit n of the character

If used, the parity bit is located between the last data bit and first stop bit of a serial frame.

18.5

USART Initialization

The USART has to be initialized before any communication can take place. The initialization pro-

cess normally consists of setting the baud rate, setting frame format and enabling the

Transmitter or the Receiver depending on the usage. For interrupt driven USART operation, the

Global Interrupt Flag should be cleared (and interrupts globally disabled) when doing the

initialization.

Before doing a re-initialization with changed baud rate or frame format, be sure that there are no

ongoing transmissions during the period the registers are changed. The TXCn Flag can be used

to check that the Transmitter has completed all transfers, and the RXCn Flag can be used to

check that there are no unread data in the receive buffer. Note that the TXCn Flag must be

cleared before each transmission (before UDRn is written) if it is used for this purpose.

The following simple USART initialization code examples show one assembly and one C func-

tion that are equal in functionality. The examples assume asynchronous operation using polling

(no interrupts enabled) and a fixed frame format. The baud rate is given as a function parameter.

Peven

dn 1

–

…

Podd

⊕

⊕⊕⊕⊕⊕

dn 1

–

…

⊕

⊕⊕⊕⊕⊕

ATmega325P 데이터시트(PDF) 169 Page - ATMEL Corporation

ATmega325P 데이터시트(HTML) 169 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL