| 전자부품 데이터시트 검색엔진 |
|
NX2113 데이터시트(PDF) 14 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
NX2113 데이터시트(HTML) 14 Page - Microsemi Corporation |
|
14 / 19 page ![]() NX2113/2113A 14 Rev. 2.0 11/18/05 5. Calculate C 1 by setting compensator zero FZ at 75% of the LC double pole. 1 3z 1 C = 2 RF 1 = 2 10k 0.75 6.5kHz =10.7nF ×π ×× ×π × Ω ×× Choose C 1=10nF. 6. Calculate C 2 by setting compensator pole p F at half the swithing frequency. 2 3s 1 C = RF 1 = 10 k 300k Hz =106pF π ×× π × Ω× Choose C 2=100pF. Output Voltage Calculation Output voltage is set by reference voltage and external voltage divider. The reference voltage is fixed at 0.8V. The divider consists of two ratioed resistors so that the output voltage applied at the Fb pin is 0.8V when the output voltage is at the desired value. The following equation and picture show the relationship between OUT V , REF V and voltage divider.. 2 REF 1 OUT REF RV R= V -V × ...(18) whereR2 is part of the compensator, and the value of R1 value can be set by voltage divider. Choose R2=10k Ω, to set the output voltage at 1.6V, the result of R1 is 10k Ω. Vout Vref Fb R2 R1 Voltage divider Figure 13 - Voltage divider load In general, the minimum output load impedance including the resistor divider should be less than 5k Ω to prevent overcharge the output voltage by leakage cur- rent (e.g. Error Amplifier feedback pin bias current). A minimum load for 5k Ω less (<1/16w for most of applica- tion) is recommended to put at the output. For example, in this application, Vout=1.6V The power loss is 1/16W less LOAD R 1.6V 1.6V /(1/16W) 40 = × =Ω Select minimum load is 1k Ω should be good enough. Input Capacitor Selection Input capacitors are usually a mix of high frequency ceramic capacitors and bulk capacitors. Ceramic ca- pacitors bypass the high frequency noise, and bulk ca- pacitors supply current to the MOSFETs. Usually 1uF ceramic capacitor is chosen to decouple the high fre- quency noise. The bulk input capacitors are decided by voltage rating and RMS current rating. The RMS current in the input capacitors can be calculated as: RMS OUT OUT IN I I D 1-D V D V = ×× = ...(19) VIN = 12V, VOUT=1.6V, IOUT=10A, using equation (19), the result of input RMS current is 3.4A. For higher efficiency, low ESR capacitors are recommended. One Sanyo OSCON SP series 16SP270M 16V 270uF with 4.4A is chosen as input bulk capacitor. Power MOSFETs Selection The NX2113 requires two N-Channel power MOSFETs. The selection of MOSFETs is based on maximum drain source voltage, gate source voltage, maximum current rating, MOSFET on resistance and power dissipation. The main consideration is the power loss contribution of MOSFETs to the overall converter efficiency. In this design example, two IRFR3706 are used. They have the following parameters: V DS=30V, ID =75A,R DSON =9mΩ,QGATE =23nC. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |