| 전자부품 데이터시트 검색엔진 |
|
PIC16F707T-E/ML 데이터시트(PDF) 65 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16F707T-E/ML 데이터시트(HTML) 65 Page - Microchip Technology |
|
65 / 284 page ![]() 2010 Microchip Technology Inc. Preliminary DS41418A-page 65 PIC16F707/PIC16LF707 6.6 PORTE and TRISE Registers PORTE is a 4-bit wide, bidirectional port. The corresponding data direction register is TRISE. Setting a TRISE bit (= 1) will make the corresponding PORTE pin an input (i.e., put the corresponding output driver in a High-Impedance mode). Clearing a TRISE bit (= 0) will make the corresponding PORTE pin an output (i.e., enable the output driver and put the contents of the output latch on the selected pin). The exception is RE3, which is input only and its TRIS bit will always read as ‘1’. Example 6-5 shows how to initialize PORTE. Reading the PORTE register (Register 6-16) reads the status of the pins, whereas writing to it will write to the PORT latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, this value is modified and then written to the PORT data latch. RE3 reads ‘0’ when MCLRE = 1. The TRISE register (Register 6-17) controls the PORTE pin output drivers, even when they are being used as analog inputs. The user should ensure the bits in the TRISE register are maintained set when using them as analog inputs. I/O pins configured as analog input always read ‘0’. EXAMPLE 6-5: INITIALIZING PORTE 6.6.1 ANSELE REGISTER The ANSELE register (Register 6-18) is used to configure the Input mode of an I/O pin to analog. Setting the appropriate ANSELE bit high will cause all digital reads on the pin to be read as ‘0’ and allow analog functions on the pin to operate correctly. The state of the ANSELE bits has no affect on digital output functions. A pin with TRIS clear and ANSELE set will still operate as a digital output, but the Input mode will be analog. This can cause unexpected behavior when executing read-modify-write instructions on the affected port. Note: The ANSELE register must be initialized to configure an analog channel as a digital input. Pins configured as analog inputs will read ‘0’. BANKSEL PORTE ; CLRF PORTE ;Init PORTE BANKSEL ANSELE ; CLRF ANSELE ;digital I/O BANKSEL TRISE ; MOVLW B‘00001100’ ;Set RE<2> as an input MOVWF TRISE ;and set RE<1:0> ;as outputs REGISTER 6-16: PORTE: PORTE REGISTER U-0 U-0 U-0 U-0 R-x R/W-x R/W-x R/W-x — — — — RE3 RE2 RE1 RE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-4 Unimplemented: Read as ‘0’ bit 3-0 RE<3:0>: PORTE I/O Pin bits 1 = Port pin is > VIH 0 = Port pin is < VIL |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |