PIC16F882_09 datasheet(69/328 Pages) MICROCHIP

69 / 328 page

DS41291F-page 67

PIC16F882/883/884/886/887

4.5.3

LFINTOSC

The Low-Frequency Internal Oscillator (LFINTOSC) is

an uncalibrated 31 kHz internal clock source.

The output of the LFINTOSC connects to a postscaler

and multiplexer (see Figure 4-1). Select 31 kHz, via

software, using the IRCF<2:0> bits of the OSCCON

(IRCF)” for more information. The LFINTOSC is also the

frequency for the Power-up Timer (PWRT), Watchdog

Timer (WDT) and Fail-Safe Clock Monitor (FSCM).

The LFINTOSC is enabled by selecting 31 kHz

(IRCF<2:0> bits of the OSCCON register = 000) as the

system clock source (SCS bit of the OSCCON

• Two-Speed Start-up IESO bit of the Configuration

Word Register 1 = 1 and IRCF<2:0> bits of the

OSCCON register = 000

• Power-up Timer (PWRT)

• Watchdog Timer (WDT)

• Fail-Safe Clock Monitor (FSCM)

The LF Internal Oscillator (LTS) bit of the OSCCON

not.

4.5.4

FREQUENCY SELECT BITS (IRCF)

The output of the 8 MHz HFINTOSC and 31 kHz

LFINTOSC connects to a postscaler and multiplexer

(see Figure 4-1). The Internal Oscillator Frequency

Select bits IRCF<2:0> of the OSCCON register select

the frequency output of the internal oscillators. One of

eight frequencies can be selected via software:

•8 MHz

• 4 MHz (Default after Reset)

•2 MHz

•1 MHz

• 500 kHz

• 250 kHz

• 125 kHz

• 31 kHz (LFINTOSC)

4.5.5

HFINTOSC AND LFINTOSC CLOCK

SWITCH TIMING

When switching between the LFINTOSC and the

HFINTOSC, the new oscillator may already be shut

down to save power (see Figure 4-6). If this is the case,

there is a delay after the IRCF<2:0> bits of the

OSCCON register are modified before the frequency

selection takes place. The LTS and HTS bits of the

OSCCON register will reflect the current active status

of the LFINTOSC and HFINTOSC oscillators. The

timing of a frequency selection is as follows:

IRCF<2:0> bits of the OSCCON register are

modified.

If the new clock is shut down, a clock start-up

delay is started.

Clock switch circuitry waits for a falling edge of

the current clock.

CLKOUT is held low and the clock switch

circuitry waits for a rising edge in the new clock.

CLKOUT is now connected with the new clock.

LTS and HTS bits of the OSCCON register are

updated as required.

Clock switch is complete.

See Figure 4-1 for more details.

If the internal oscillator speed selected is between

8 MHz and 125 kHz, there is no start-up delay before

the new frequency is selected. This is because the old

and new frequencies are derived from the HFINTOSC

via the postscaler and multiplexer.

Start-up delay specifications are located in the

oscillator

tables

Section 17.0

“Electrical

Specifications”.

Note:

Following any Reset, the IRCF<2:0> bits of

the OSCCON register are set to ‘110’ and

the frequency selection is set to 4 MHz.

The user can modify the IRCF bits to

select a different frequency.

PIC16F882 데이터시트(PDF) 69 Page - Microchip Technology

PIC16F882 데이터시트(HTML) 69 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL