| 전자부품 데이터시트 검색엔진 |
|
PCF8532 데이터시트(PDF) 30 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCF8532 데이터시트(HTML) 30 Page - NXP Semiconductors |
|
30 / 44 page ![]() PCF8532_1 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 1 — 10 February 2009 30 of 44 NXP Semiconductors PCF8532 Universal LCD driver for low multiplex rates 11. Dynamic characteristics [1] Typical output duty factor: 50 % measured at the CLK output pin. [2] For fclk(ext) > 4 kHz it is recommended to use an external pull-up resistor between pin SYNC and pin VDD. The value of the resistor should be between 100 k Ω and 1 MΩ. This resistor should be present even when no cascading configuration is used! [3] All timing values are valid within the operating supply voltage and ambient temperature range and are referenced to VIL and VIH with an input voltage swing of VSS to VDD. Table 18. Dynamic characteristics VDD = 1.8 V to 5.5 V; VSS = 0 V; VLCD = 2.5 V to 8.0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fclk clock frequency on pin CLK; see Table 15 [1] 900 1800 3000 Hz fclk(ext) external clock frequency [2] 700 - 5000 Hz tclk(H) HIGH-level clock time external clock source used 100 - - µs tclk(L) LOW-level clock time external clock source used 100 - - µs tPD(SYNC_N) SYNC propagation delay - 30 - ns tSYNC_NL SYNC LOW time 100 - - µs tPD(drv) driver propagation delay VLCD = 5 V - 10 - µs Timing characteristics: I2C-bus [3] fSCL SCL clock frequency - - 400 kHz tBUF bus free time between a STOP and START condition 1.3 - - µs tHD;STA hold time (repeated) START condition 0.6 - - µs tSU;STA set-up time for a repeated START condition 0.6 - - µs tVD;ACK data valid acknowledge time - - 1.2 µs tHIGH HIGH period of the SCL clock 0.6 - - µs tLOW LOW period of the SCL clock 1.3 - - µs tf fall time of both SDA and SCL signals - - 0.3 µs tr rise time of both SDA and SCL signals - - 0.3 µs Cb capacitive load for each bus line - - 400 pF tSU;DAT data set-up time 200 - - ns tHD;DAT data hold time 0 - - ns tSU;STO set-up time for STOP condition 0.6 - - µs tw(spike) spike pulse width - - 50 ns |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |