22017 datasheet(65/120 Pages) ITT

65 / 120 page

ARINC 404

DPX*MA Crimp

Coaxial Cable Assembly Recommendations (Continued)

www.ittcannon.com

Dimensions shown in inch (mm)

Specifications and dimensions subject to change

For Code V

1. Trim cable to dimensions shown below.

A. Push ferrule under braid as far as it will go and press braid down tightly around ferrule.

B. Solder ends of braid to ferrule by applying a small amount of solder. Avoid excess solder as it would

cause braid to swell up.

C. Remove any solder exceeding the .349 (8.86) max. diameter.

D. Check the .075 (1.90) max. dielectric extension, retrim if necessary.

3. A. Place rear insulator over dielectric and conductor into contact.

B. Solder contact to conductor through access hole.

C. Remove excess solder from outside of contact.

4. A. Place front insulator over contact.

B. Push parts into coaxial shell.

C. While holding parts firmly against stop shoulder in coaxial shell, place jaw of crimp tool at back end

of shell and crimp, use Buchanan crimp tool #612991 [.343 (8.71) across hex].

For Codes AB, AD, AE, AF and AG

Setp 1 - Trim cable as shown.

Step 2 - Flare out ends of braid to permit entry of ferrule.

Step 3 - Complete termination per instructions as shown below.

a. Push ferrule under braid as far as it will go. Trim off braid extending beyond shoulder of ferrul, if

necessary.

b. While holding ferrule in place pull crimp sleeve forward over braid until it is tight against shoulder on

ferrule. Push firmly against face of ferrule to make sure it is up tight.

c. Trim dielectric to the .035 (0.89)/ .030 (0.76) dimension.

d. Carefully push inner conductor through rear insulator.

e. While holding rear insulator firmly against ferrule, trim conductor to .156 (3.96)/.146 (3.71)

dimension.

f. Place contact over conductor and solder.

g. Place front insulator over contact and then push assembly into coaxial shell.

h. Place parts in jaw of crimp tool. Locate jaws at start of chamfer on crimp sleeve. Press

Sleeve firmly into coaxial shell and crimp. Use Daniels crimp tool HX4-210.

Code

Letter

B, C, D & P

H & R

AA, AC

AB, AD, AE, AF, AG

.420/.400

.785/.745

.490/.470

.581/.561

.326/.306

.410/.390

.385/.365

.678/.658

.940/.920

.550/.540

.598/.578

.432/.415

.460/.440

.480/.460

.275/.255

.345/.325

.250/.230

.290/.270

.244/.224

.275/.255

.760/.740

.415/.405

.300/.280

.330/.310

.228/.208

.156/.136

.088/.068

.074/.064

.156/.136

.080/.060

.250/.240

.228/.208

See page 60 for dimensions

.10.67/10.16

10.67/10.16

19.94/18.92

12.45/11.94

14.76/14.25

8.28/7.77

10.41/9.91

9.78/9.27

17.22/16.71

23.88/23.37

13.97/13.72

15.19/14.68

11.05/10.54

11.68/11.18

12.19/11.68

6.98/6.48

8.76/8.26

6.35/5.84

7.37/6.86

6.20/5.69

6.98/6.48

19.30/18.80

10.54/10.29

7.62/7.11

8.38/7.87

5.79/5.28

3.96/3.45

2.24/1.73

1.88/1.63

3.96/3.45

2.03/1.52

6.35/6.10

5.79/5.28

INNER CONDUCTOR

CRIMP AREA

REAR INSULATOR

CONTACT

Crimp Sleeve

.400 APPROX.

(10.16)

FRONT INSULATOR

0.75 MAX.

(1.90)

.349 DIA. MAX

(8.86)

SOLDER ALL AROUND

FERRULE

.156 (3.96)

.146 (3.71)

.035 (0.89)

.030 (0.76)

.260 (6.60)

.250 (6.35)

.610 (15.49)

.590 (14.99)

FRONT INSULATOR

COAXIAL SHELL

.350 APPROX

(8.89)

DIELECTRIC

BRAID

JACKET

Inches

Millimeters

Cable Trim Dimensions

22017 데이터시트(PDF) 65 Page - ITT Industries

22017 데이터시트(HTML) 65 Page - ITT Industries

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL