| 전자부품 데이터시트 검색엔진 |
|
LPC1850 데이터시트(PDF) 71 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC1850 데이터시트(HTML) 71 Page - NXP Semiconductors |
|
71 / 149 page ![]() LPC1850_30_20_10 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved. Product data sheet Rev. 6.1 — 7 February 2013 71 of 149 NXP Semiconductors LPC1850/30/20/10 32-bit ARM Cortex-M3 microcontroller • MultiMedia Cards (MMC version 4.4) 7.13.5 External Memory Controller (EMC) The LPC1850/30/20/10 EMC is a Memory Controller peripheral offering support for asynchronous static memory devices such as RAM, ROM, and NOR flash. In addition, it can be used as an interface with off-chip memory-mapped devices and peripherals. 7.13.5.1 Features • Dynamic memory interface support including single data rate SDRAM. • Asynchronous static memory device support including RAM, ROM, and NOR flash, with or without asynchronous page mode. • Low transaction latency. • Read and write buffers to reduce latency and to improve performance. • 8/16/32 data and 24 address lines-wide static memory support. On parts LPC1820/10 only 8/16 data lines are available. • 16-bit and 32-bit wide chip select SDRAM memory support. • Static memory features include: – Asynchronous page mode read – Programmable Wait States – Bus turnaround delay – Output enable and write enable delays – Extended wait • Four chip selects for synchronous memory and four chip selects for static memory devices. • Power-saving modes dynamically control EMC_CKEOUT and EMC_CLK signals to SDRAMs. • Dynamic memory self-refresh mode controlled by software. • Controller supports 2048 (A0 to A10), 4096 (A0 to A11), and 8192 (A0 to A12) row address synchronous memory parts. Those are typically 512 MB, 256 MB, and 128 MB parts, with 4, 8, 16, or 32 data bits per device. • Separate reset domains allow auto-refresh through a chip reset if desired. Note: Synchronous static memory devices (synchronous burst mode) are not supported. 7.13.6 High-speed USB Host/Device/OTG interface (USB0) Remark: USB0 is available on parts LPC1850/30/20 (see Table 2). The USB OTG module allows the part to connect directly to a USB host such as a PC (in device mode) or to a USB device in host mode. 7.13.6.1 Features • On-chip UTMI+ compliant high-speed transceiver (PHY). • Complies with Universal Serial Bus specification 2.0. • Complies with USB On-The-Go supplement. • Complies with Enhanced Host Controller Interface Specification. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |