MCP6546-ISLASHMS datasheet(2/44 Pages) MICROCHIP

2 / 44 page

MCP6546/6R/6U/7/8/9

DS21714G-page 2

1.0

ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

VDD - VSS .........................................................................7.0V

Open-Drain Output.............................................. VSS + 10.5V

Analog Input (VIN+, VIN-)††............. VSS - 1.0V to VDD + 1.0V

All Other Inputs and Outputs ......... VSS – 0.3V to VDD + 0.3V

Difference Input Voltage ...................................... |VDD – VSS|

Output Short-Circuit Current .................................continuous

Current at Input Pins ....................................................±2 mA

Current at Output and Supply Pins ............................±30 mA

Storage Temperature.....................................-65°C to +150°C

Maximum Junction Temperature (TJ) .......................... +150°C

ESD Protection on All Pins:

(HBM;MM) .....................................2 kV;200V (MCP6546U)

(HBM;MM) ................................ 4 kV; 200V (all other parts)

† Notice: Stresses above those listed under “Absolute

Maximum Ratings” may cause permanent damage to

the device. This is a stress rating only, and functional

operation of the device, at those or any other conditions

above those indicated in the operational listings of this

specification, is not implied. Exposure to maximum rat-

ing conditions for extended periods may affect device

reliability.

†† See Section 4.1.2 “Input Voltage and Current

Limits”

DC CHARACTERISTICS

Electrical Specifications: Unless otherwise indicated, VDD = +1.6V to +5.5V, VSS = GND, TA = 25°C, VIN+ = VDD/2,

VIN– = VSS, RPU =2.74 kΩ to VPU = VDD (Refer to Figure 1-3).

Parameters

Sym

Min

Typ

Max

Units

Conditions

Power Supply

Supply Voltage

VDD

1.6

—

5.5

VPU ≥ VDD

Quiescent Current

(per comparator)

0.3

0.6

µA

IOUT = 0

Input

Input Voltage Range

VCMR

VSS −

0.3

—VDD + 0.3

Common Mode Rejection Ratio

CMRR

—

VDD = 5V, VCM = -0.3V to 5.3V

Common Mode Rejection Ratio

CMRR

—

VDD = 5V, VCM = 2.5V to 5.3V

Common Mode Rejection Ratio

CMRR

—

VDD = 5V, VCM = -0.3V to 2.5V

Power Supply Rejection Ratio

PSRR

—

VCM = VSS

Input Offset Voltage

VOS

-7.0

±1.5

+7.0

VCM = VSS (Note 1)

Drift with Temperature

ΔV

OS/ΔTA

—

±3

—

µV/°C TA = -40°C to +125°C, VCM = VSS

Input Hysteresis Voltage

VHYST

1.5

3.3

6.5

VCM = VSS (Note 1)

Linear Temp. Co.

TC1

—6.7

—

µV/°C TA = -40°C to +125°C, VCM = VSS

(Note 2)

Quadratic Temp. Co.

TC2

—-0.035

—

µV/°C2 TA = -40°C to +125°C, VCM = VSS

(Note 2)

Input Bias Current

—1

—

VCM = VSS

At Temperature (I-Temp parts)

—

100

TA = +85°C, VCM = VSS (Note 3)

At Temperature (E-Temp parts)

—

1200

5000

TA = +125°C, VCM = VSS (Note 3)

Input Offset Current

IOS

—

±1

—

VCM = VSS

Note 1:

The input offset voltage is the center of the input-referred trip points. The input hysteresis is the difference

between the input-referred trip points.

VHYST at differential temperatures is estimated using:

VHYST (TA) = VHYST + (TA -25°C) TC1 + (TA - 25°C)

2TC

Input bias current at temperature is not tested for the SC-70-5 package.

Do not short the output above VSS + 10V. Limit the output current to Absolute Maximum Rating of 30 mA.

The minimum VPU test limit was VDD before Dec. 2004 (week code 52).

MCP6546-I/MS 데이터시트(PDF) 2 Page - Microchip Technology

MCP6546-I/MS 데이터시트(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

데이터시트 다운로드

링크 URL