STLUX385ATR datasheet(70/99 Pages) STMICROELECTRONICS

70 / 99 page

Electrical characteristics

STLUX385A

70/98

DocID024387 Rev 2

10.2

Absolute maximum ratings

Stresses above those listed as 'absolute maximum ratings' may cause permanent damage

to the device. This is a stress rating only and functional operation of the device under these

conditions is not implied. Exposure to maximum rating conditions for extended periods may

affect the device reliability.

Table 32. Voltage characteristics

Symbol

Ratings

Min.

Max.

Unit

DDX

– V

SSX

Supply voltage

(1)

All power V

DDX

, V

DDA

) and ground V

SSX

, V

SSA

) pins must always be connected to the external

power supply.

-0.3

6.5

Input voltage on any other pin

(2)

INJ(PIN)

must never be exceeded. This is implicitly insured if V

maximum is respected. If V

maximum

cannot be respected, the injection current must be limited externally to the I

INJ(PIN)

value. A positive

injection is induced by V

> V

while a negative injection is induced by V

< V

-0.3

+0.3

- V

DDA

Variation between different power pins

- V

SSA

Variation between all the different ground

pins

(3)

and V

SSA

signals must be interconnected together with a short wire loop.

ESD

Electrostatic discharge voltage

Refer to absolute maximum ratings

(electrical sensitivity) on

Section 10.4.1

Table 33. Current characteristics

Symbol

Ratings

Max.(1)

Data based on characterization results, not tested in production.

Unit

VDDX

Total current into V

DDX

power lines

(2)

All power V

DDX

, V

DDA

) and ground V

SSX

, V

SSA

) pins must always be connected to the external

power supply.

100

VSSX

Total current out of V

SSX

power lines

(2)

100

Output current sunk by any I/Os and control pin

Ref.

Output current source by any I/Os and control pin

INJ(PIN)

(3) (4)

INJ(PIN)

must never be exceeded. This is implicitly insured if V

maximum is respected. If V

maximum

cannot be respected, the injection current must be limited externally to the I

INJ(PIN)

value. A positive

injection is induced by V

> V

while a negative injection is induced by V

< V

Negative injection disturbs the analog performance of the device.

Injected current on any pin

±4

INJ(TOT)

(3)(4)(5)

When several inputs are submitted to a current injection, the maximum

IINJ(PIN)

is the absolute sum of the

positive and negative injected currents (instantaneous values). These results are based on characterization

with

IINJ(PIN)

maximum current injection on four I/O port pins of the device.

Sum of injected currents

±20

STLUX385ATR 데이터시트(PDF) 70 Page - STMicroelectronics

STLUX385ATR 데이터시트(HTML) 70 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99

데이터시트 다운로드

링크 URL