PIC16F1825T-ESS datasheet(62/448 Pages) MICROCHIP

62 / 448 page

PIC16(L)F1825/1829

DS41440C-page 62

 2010-2012 Microchip Technology Inc.

5.2.2.5

Internal Oscillator Frequency

Selection

The system clock speed can be selected via software

using the Internal Oscillator Frequency Select bits

IRCF<3:0> of the OSCCON register.

The outputs of the 16 MHz HFINTOSC postscaler and

the LFINTOSC connect to multiplexer (see Figure 5-1).

The

Internal

Oscillator

Frequency

Select

bits

IRCF<3:0> of the OSCCON register select the

frequency output of the internal oscillators. One of the

following frequencies can be selected via software:

• 32 MHz (requires 4xPLL)

•16 MHz

•8 MHz

•4 MHz

•2 MHz

•1 MHz

• 500 kHz (default after Reset)

• 250 kHz

• 125 kHz

• 62.5 kHz

• 31.25 kHz

• 31 kHz (LFINTOSC)

The IRCF<3:0> bits of the OSCCON register allow

duplicate selections for some frequencies. These

duplicate choices can offer system design trade-offs.

Lower power consumption can be obtained when

changing oscillator sources for a given frequency.

Faster transition times can be obtained between

frequency changes that use the same oscillator source.

5.2.2.6

32 MHz Internal Oscillator

Frequency Selection

The Internal Oscillator Block can be used with the

4xPLL associated with the External Oscillator Block to

produce a 32 MHz internal system clock source. The

following settings are required to use the 32 MHz

internal clock source:

• The FOSC bits in Configuration Word 1 must be

set to use the INTOSC source as the device

system clock (FOSC<2:0> = 100).

• The SCS bits in the OSCCON register must be

cleared to use the clock determined by

FOSC<2:0> in Configuration Word 1

(SCS<1:0> = 00).

• The IRCF bits in the OSCCON register must be

set to the 8 MHz HFINTOSC set to use

(IRCF<3:0> = 1110).

• The SPLLEN bit in the OSCCON register must be

set to enable the 4xPLL, or the PLLEN bit of the

Configuration Word 2 must be programmed to a

‘1’.

The 4xPLL is not available for use with the internal

oscillator when the SCS bits of the OSCCON register

are set to ‘1x’. The SCS bits must be set to ‘00’ to use

the 4xPLL with the internal oscillator.

Note:

Following any Reset, the IRCF<3:0> bits

of the OSCCON register are set to ‘0111’

and the frequency selection is set to

500 kHz. The user can modify the IRCF

bits to select a different frequency.

Note:

When using the PLLEN bit of the

Configuration Word 2, the 4xPLL cannot

be disabled by software and the 8 MHz

HFINTOSC option will no longer be

available.

PIC16F1825T-ESS 데이터시트(PDF) 62 Page - Microchip Technology

PIC16F1825T-ESS 데이터시트(HTML) 62 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL